47516

Oce OP15 Operations Guide Printing System Functions Manual

20
Zoom out
Zoom in
Previous page
1/87
Next page
2-9
2. Printer Settings (20 ppm copier)
Item No.
23
24
25
26
27
28
29
30
31
32
33
34
Item
Page Protect
If “AUTO” is selected here, the machine will
monitor the data and, if necessary, will
automatically turn Page Protect ON. If a
“Print overrun” error does happen to occur
even then, the machine will automatically
change the Page Protect setting to “ON”.
Line Feed (LF) handling
Carriage Return (CR) handling
Wide A4 ON/OFF
Increases the printing area on A4 size paper.
Smoothing ON/OFF
Allows a printing resolution of an interpo-
lated 2400 dpi x 600 dpi through the
smoothing process.
Draft Mode ON/OFF
Allows printing in a toner-saving mode. This
mode is especially suited for test pages, etc.,
where high printing quality is not required.
Printing resolution
RAM disk ON/OFF
RAM disk size
Sets the amount of memory that will be used
as a RAM disk. The maximum size that can
be selected is the total amount of memory
installed minus the amount used by the
system (9 MB).
Reading data
Reads the selected data on the RAM disk.
Reading program data
Reads the selected program data on the
RAM disk.
Writing data
If “OK” is selected here, the machine will
enter a “waiting for data” state until data is
sent from the host computer. To exit this
state, select the “GO” command in the
printer mode and then press the Enter key.
Display message
Page Protect
LF Action
CR Action
Wide A4
KIR Mode
Draft
Resolution
RAM DISK Mode
RAM DISK Size
Read Data
Read Program
Write Data
Available settings
Auto, On
LF only,
CR and LF,
Ignore LF
CR only,
CR and LF,
Ignore CR
On, Off
On, Off
On, Off
300 dpi, 600 dpi
On, Off
01 - 99 (MBytes)
Select the name of
the partition which
holds the data from
among those
displayed.
Select the name of
the partition which
holds the program
from among those
displayed.
OK
Remarks
Allows you to set different line
feed handling for the parallel
interface and the Network Card
(option). Select the desired
interface under the “Interface
selection” setting (item No.: 2).
Allows you to set different carriage
return handling for the parallel
interface and the Network Card
(option). Select the desired
interface under the “Interface
selection” setting (item No.: 2).
At least 16 MB of additional
memory (option) must be installed.
Displayed only when “On” is
selected under the “RAM disk ON/
OFF” setting (item No.: 30).
Displayed only when there is
appropriate data in the RAM disk.
Displayed only when there is
appropriate program data in the
RAM disk.
Displayed only when “On” is
selected under the “RAM disk ON/
OFF” setting (item No.: 30).
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oce OP15 Operations Guide Printing System Functions at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oce OP15 Operations Guide Printing System Functions in the language / languages: English as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info