47423
15
Zoom out
Zoom in
Previous page
1/24
Next page
9
3. Troubleshooting
3-2 When an error message appears
If an error message appears on the operation panel, first check the following tables for cause of the trouble and then perform the corresponding
procedure. For more detailed information, refer to the Operation Guide for your copier as well as the Operation Guide for any optional equipment
that is installed in your machine.
Display message
Add paper in drawer (cassette).
XX size (XXX)
Use alternative? Press GO
Set paper Press GO
Place paper.
Add staples.
Call service.
Department code mismatch
Exceeded print quantity limit.
Exceeded pre-registered printing quantity.
Error in printer mode
RAM Disk error Press GO
Procedure
The size or type of paper selected for printing does not match the size or type of paper in the
cassette. Replace the paper in the drawer with that of the correct size and type.
If you want to switch to and print from a different cassette, select the desired cassette on
the touch panel and then touch the GO key.
The following commands will be displayed in the printer mode.
GO: Force-prints onto the current size or type of paper.
Cancel: Cancels the printing operation completely.
Displayed after changing the drawer. Touch the GO key.
This mode feeds a stack of multiple sheets one at a time. Every time you want to feed a
sheet, touch the GO key.
The cassette has run out of paper. Add paper.
The finisher (option) has run out of staples. Refer to the Operation Guide for the finisher and
replenish the staples.
Trouble has occurred within the printer. Contact your service representative or an authorized
service center.
The department code you entered does not match the registered one. Check the department
code that is registered in the printer driver.
The amount of printing accomplished has exceeded the acceptable capacity as set under
copy management. In order to print further, change the copy management setting in the
printer.
This message will appear when a printer error occurs and the machine is in a mode other
than the printer mode. Press the Printer key to switch to the print mode screen and the
corresponding error message will be displayed.
Code:##
Check the error code displayed in place of ## and refer to the following.
01: Format error. Turn power Off and On again.
02: The RAM disk mode is Off. Turn it On.
03: A write error has occurred. Turn Off write protection.
04: The RAM disk does not have enough area to store the data. Delete any unnecessary
data to make more room.
05: The selected file could not be found. Check the file name and whether it is on the RAM
disk or not.
06: There is not enough system memory. Increase memory capacity.
98: Some of the data being collated was not read. Job data is corrupt.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oce OP1040 Operations Guide Printing System Set-up at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oce OP1040 Operations Guide Printing System Set-up in the language / languages: English as an attachment in your email.

The manual is 2,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info