46595
11
Zoom out
Zoom in
Previous page
1/16
Next page
4
2. Set-up
2-3 Network (TCP/IP) settings
When the optional Network Card is installed and this machine is to
be used as a network printer, it is necessary to set the corresponding
IP address for the printer.
Notes
The IP address that should be registered here will differ depending
upon your network environment. Check with your network
administrator BEFORE performing this setting.
If you are using a DHCP server to automatically configure the IP
address, this setting will not be necessary because DHCP server
configuration is already enabled as the factory default setting.
* To cancel the setting midway through it, press the Stop/Reset key.
Press the Printer key. The machine will switch to the printer
mode and P00 will appear in the copy quality/magnification
display.
Use the (+) and () keys to select 23 and then press the
Enter key. The display will change to P23 (the TCP/IP ON/
OFF setting).
Use the (+) and () keys to select 1 (On) and then press
the Enter key. The selected setting will flash twice and will
then be registered.
Use the (+) and () keys to select 24 and then press the
Enter key. The display will change to P24 (the DHCP ON/
OFF setting).
1
2
3
4
5
Use the (+) and () keys to select 2 (Off) and then press
the Enter key. The selected setting will flash twice and will
then be registered.
Use the (+) and () keys to select 25 and then press the
Enter key. The display will change to P25 (the IP address
setting).
The (+) and () keys will be used to select the 12-digit IP
address in blocks of 3 digits each:
First, enter the appropriate 3 digits for the first block and
then press the Enter key. Repeat this same procedure for
the 3 remaining blocks of the address (4 blocks in all). Once
the Enter key is pressed for the final 3-digit block, the
display will flash twice and the IP address will be registered.
Use the (+) and () keys to select 26 and then press the
Enter key. The display will change to P26 (the Subnet
Mask setting). Enter the 12-digit Subnet Mask using the
same procedure that you did for entering the IP address.
Use the (+) and () keys to select 27 and then press the
Enter key. The display will change to P27 (the Gateway
address setting). Enter the 12-digit Gateway address using
the same procedure that you did for entering the IP address.
Once you are finished making all of the network settings,
press the Printer key. The machine will switch back to the
copier mode.
6
7
8
9
10
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oce Oce OP14 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oce Oce OP14 in the language / languages: English as an attachment in your email.

The manual is 0,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info