663182

NuVinci Nfinity 330 Manual

15
Zoom out
Zoom in
Previous page
1/120
Next page
15
EN
TECHNICAL OWNER MANUAL
3.7 Installing Shift Cables and Hardware
Install cable end hardware only by pulling
cables at the end of the housing (A). Never
rotate the grip (B) with cables unattached, as
they can bind inside the shifter.
1. Pass the shift cables through the
appropriate cable housing and ensure
the housing is seated completely into the
shifter.
• Thread both barrel adjusters completely
clockwise (in) to provide maximum
installation slack.
2. Pull the underdrive shift cable (C) firmly
at the rear axle location until it stops,
checking to make sure that the shift
indicator (D) goes completely flat (Nfinity
C8 and Nfinity C8s shifters), or that the
grip rotates fully in the counter-clockwise
direction shown (Nfinity C3 shifter, viewed
from right side of bicycle).
3. Pass the underdrive shift cable through the
UD cable stop (F) and secure the UD cable
stop at the distance shown (E) while pulling
the cable firmly.
• Ensure that the cable housing is seated fully
at the shifter.
• Using a 2mm allen, secure the cable and
torque to 1.5-2.0 Nm (13-18 in-lbs).
NFINITY ASSEMBLY OF COMPONENTS
4. Cut the excess cable at a maximum of
2.0mm from the end of the UD cable stop
(G).
5. Pull the overdrive shift cable (H) firmly
at the Nfinity Hub Interface until it stops,
checking to make sure that the shift
indicator (I) goes into a steep hill (Nfinity
C8 and Nfinity C8s shifters), or that the
grip rotates fully in the clockwise direction
shown (Nfinity C3 shifter, viewed from
right side of bicycle).
• Make sure the underdrive shift cable and
UD cable stop are free and unobstructed
6. Pass the overdrive shift cable through the
OD Latch (K) and secure the OD latch at
the distance shown (J) while pulling the
cable firmly.
• Ensure that the cable housing is seated fully
at the shifter.
• Using a 2mm allen, secure the cable and
torque to 1.5-2.0 Nm (13-18 in-lbs).
7. Cut the excess cable at the OD latch
marking (L), and tuck the remaining cable
length into the OD latch as shown (M).
8. The cable hardware should appear as
shown. Assemble to CVP per section 2.5
and adjust cable slack with the barrel
adjusters per section 2.3.
E
C
B
F
G
A
D
120 mm*
H
I
J
L
K
M
114 mm*
*120mm for Standard shifter and 82mm for One-Turn
*114mm for Standard shifter and 102mm for One-Turn
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NuVinci Nfinity 330 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NuVinci Nfinity 330 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 11,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info