564479
22
Zoom out
Zoom in
Previous page
1/28
Next page
22
Green Status Indicator Fault Possible Cause Effect on Product Investigate the Following Action Required If fault persists
1 Flash with pause Batteries voltage low Batteries not been charged
Possible bad connection between
batteries, controller, charger or fuses
caused by loose connections,
damaged wiring, water ingress
Not accepting charge due to faulty
battery/cell
Charger not functioning
Operating time
severely reduced
or machine will not
operate
Check when machine last charged
Switch OFF the machine :
Remove Fuses
Check connections to batteries, charger and
fuses for loose wires or screws
Check each battery Voltage individually to
detect defect unit 10.5V min
Check battery voltage and charge current
ensuring charger red fault light is
extinguished
Charge batteries immediately
Tighten loose connections and
replace damaged components
Replace batteries as required
Replace charger
Contact
Service
Agent
2 Flashes with pause Traction motor
disconnected
The motor has a bad connection
Motor disconnected
TCO activated
(Thermal cut Out)
Motor failed open circuit
Motor will not operate Check all connections and leads between the
motor and controller
Tighten loose connections and
replace damaged
components - check exhaust
clean if necessary.
3 Flashes with pause Traction motor wiring
Trip
The motor has a short circuit to a
battery
Motor will not operate Check all connections and leads between the motor and controller
4 Flashes with pause Battery Lockout The battery charge level has fallen
below the battery lockout level and
the controller is inhibiting machine
functions
Machine functions not
working
Check battery voltage and charge current
ensuring charger red fault light is extinguished
Check each battery Voltage individually to
detect defect unit 10.5V min
Charge batteries immediately
6 Flashes with pause Charger Connected The controller is being inhibited from
driving, This may be because the
battery charger is connected
Machine functions not
working
Remove Charger to operate machine
8 Flashes with pause Controller Trip A controller trip is indicated Machine functions not
working
Check all connections and leads Tighten loose connections and
replace damaged components
9 Flashes with pause Brake Deactivated
or Failed
Poor brake connections.
Brake failure or deactivation
Traction drive
disabled
Check brake wiring and brake lever Replace brake or wiring as
necessary.
Reactivate brake by engaging
brake lever.
10 Flashes with pause High Battery Voltage Poor connections between battery
controller and traction motor
Machine functions not
working
Check each battery Voltage individually to
ensure voltage < 14 volts
Check connections on controller, batteries and
traction motor
Check combined battery pack voltage is < 28
volts
Green Flashing Warning light.
Warning light ashes explained
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Numatic TTV - 5565- 200T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Numatic TTV - 5565- 200T in the language / languages: English as an attachment in your email.

The manual is 4,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info