Manual Numatic TTB 345S (page 22 of 28) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

564469

Zoom out

Zoom in

1/28

means: -

CAUTION:

Read the instruction manual before using the appli-

ance.

WARNING:

As with all electrical equipment care and attention must be exercised at all

times during its use, in addition to ensuring that routine and preventative

maintenance is carried out periodically in order to ensure its safe operation.

Failure to carry out maintenance as necessary, including the replacement of

parts to the correct standard could render this equipment unsafe and the

manufacturer can accept no responsibility or liability in this respect.

When ordering spare parts always quote the Model Number / Serial Number

specified on the Rating Plate.

NOTE:

This machine is also suitable for commercial use, for example in hotels,

schools, hospitals, factories, shops and offices for other than normal house-

keeping purposes.

CAUTION:

This machine is not suitable for picking up hazardous dust.

CAUTION

Do not use on surfaces having a gradient exceeding that

marked on the appliance.

CAUTION

The machine is not to be stored outdoors in wet conditions.

DOS AND DONTS:

DO ensure only competent persons unpack/assemble the machine.

DO keep your machine clean.

DO keep your brushes in good condition.

DO replace any worn or damaged parts immediately.

DO regularly examine the power cord for damage, such as cracking or

ageing. If damage is found, replace the cord before further use.

DO only replace the power cord with the correct Numatic approved

replacement part.

DO ensure that the work area is clear of obstructions and / or people.

DO ensure that the working area is well illuminated.

DO pre-sweep the area to be cleaned.

DONT use steam cleaners or pressure washers to clean the machine

or use in the rain.

DONT attempt machine maintenance or cleaning unless the power

plug has been removed from the supply outlet.

DONT allow any inexperienced repairs. Call the experts

DONT strain cable or try to unplug by pulling on cable.

DONT leave the brushpad on the machine when not in use.

DONT allow the machine to be used by inexperienced or unauthorised

operators or without appropriate training.

DONT use the machine without the solution tanks properly positioned

on the machine, as shown in the instructions.

DONT expect the machine to provide trouble-free, reliable operation

unless maintained correctly.

DONT run the machine over power cable during operation.

DONT lift or pull the machine by any of the operating triggers - Use

the main handle.

DONT remove the handle from the machine except for service and

repair.

WARNING:

Only use brushes provided with the appliance or those specified in the

instruction manual. The use of other brushes may impair safety. A full

range of brushes and accessories are available for this product. Only use

brushes or pads which are suitable for the correct operation of the machine

for the specific task being performed.

WARNING:

It is essential that this equipment is correctly assembled and operated in

accordance with current safety regulations. When using the equipment

always ensure that all necessary precautions are taken to guarantee the

safety of the operator and any other persons who may be affected. Wear

non-slip footwear when Scrubbing. Use a respiratory mask in dusty envi-

ronments.

The machine, while charging, must be positioned so that the mains plug is

easily accessible.

When cleaning, servicing or maintaining the machine, replacing parts or

converting to another function the power source shall be switched off.

Mains operated machines shall be disconnected by removing the power

plug, and battery operated machines shall be disconnected by removing the

isolating pin.

NOISE AND VIBRATION

Sound Level in use (L

) < 78 dB(A)

The operators arms are subject to a vibration level of <2.5m/s

when

using the machine.

NOTE:

In some applications, noise or vibration levels may exceed the figures

stated. If noise levels exceed 85dB(A) appropriate ear protection must

be used.

PRECAUTIONS WHEN WORKING WITH BATTERIES

1. Always wear protective clothing e.g. face visor, gloves and

overalls when working with batteries

2. Whenever possible always use a properly designated and well-

ventilated area for charging. Do not smoke or bring naked flames

into the charging area.

3. Remove any metallic items from hands, wrists and neck i.e. rings,

chains etc. before working on a battery.

4. Never rest tools or metallic objects on top of the battery.

5. When charging is complete disconnect from the mains supply.

6. The batteries must be removed from the machine before it is

scrapped.

7. The machine must be disconnected from the supply when

removing the battery.

8. To remove the batteries:- Disconnect machine from the mains

supply (if charging) and ensure batteries are switched off with

circuit disconnect switch (see page 17). Disconnect hoses from

seperator and tanks. Remove seperator and tanks . Unscrew

battery strap fixings and remove. Undo battery terminals and

remove. Remove batteries.

9. The batteries are to be disposed of safely.

10.Only use genuine NUMATIC replacement batteries.

11.Do not allow the batteries to become fully discharged, it may not be

possible to recharge them. Batteries should not be discharged below

9.5 volts with 10 amps flowing.

12.Do not allow one battery to be discharged separately to the other.

13.Do not mix batteries from different machines.

14.The batteries fitted to this product are Valve Regulated Lead Acid

(VRLA) gel electrolyte type. The fitting of any other type of

battery may cause a safety hazard.

BATTERY CARE

1. Always recharge the batteries after use. This can be done at any

time  it is not necessary to wait until they are fully discharged;

they do not develop a memory.

2. Leaving the charger to operate for a minimum of 4 hours after the

green light has come on, at least weekly, will prolong battery life.

3. Do not store the machine with the batteries discharged.

Numatic International Spare Parts

Model No:TTB345/455 Handle Assembly

POS: PART NO: DESCRIPTION: COMMENTS:

1 429029 ALUMINIUM HANDLE

2 229081 HANDLE CASTING

3 229074 ADJUSTMENT GEAR

4 219010 M8 FORM A WASHER

5 219254 O-RING

6 219078 M8 STIFFNUT

7 219091 M8 X 50MM LONG HEX HEAD BOLT

8 229099 25MM DIAMETER HOLE PLUG

9 219064 M6 X 35MM LONG HEX HEAD BOLT

10 219007 M6 FORM B WASHER

11 219080 M6 DOMENUT

12 229009 HOLE BLANKING PLUG

13 329089 FRONT HANDLE MOULDING

14 229011 SWITCH PLATE

15 220598 PUSH BUTTON MICRO SWITCH

16 229028 SPRING

17 219045 M5 X 16MM LONG POZI PAN SEMS SCREW

18 220808 SWITCH COVER GASKET

19 229379 SWITCH COVER

20 219574 NYLON SPACER

21 303464 BRACKET

22 299020 M5 X 30MM LONG POZI PAN MACHINE SCREW

23 220590 LED / SWITCH PANEL

24 206316 LENS MOULDING

25 220597 PUSH BUTTON SWITCH

26 220600 SWITCH COVER

27 220725 SELF ADHESIVE LENS GASKET

28 220403 CABLE CLIP

29 329085 REAR HANDLE MOULDING

30 220390 SOCKET MOUNTING PLATE

31 220408 APPLIANCE SOCKET

32 229035 FLAP PIVOT PIN

33 229032 FLAP

34 229034 FLAP TORSION SPRING

35 229033 BLANKING PIN

36 229073 GEAR LOCKING PIN

37 229138 SPRING

38 219099 M6 HALFNUT

39 229126 LOCKING ROD

40 219017 M6 DOUBLE COIL SPRING WASHER

41 219088 M6 STIFFNUT

42 219607 RUBBER PROTECTION CAP

43 220174 NEON INDICATOR RED LENS ONLY

44 229076 SUPPORT STRIP

45 229001 RIGHTHAND SWITCH LEVER

46 229000 LEFTHAND SWITCH LEVER

47 229003 ADJUSTMENT LEVER

48 229071 LEVER MOUNTING PIN

49 227008 CABLE CLAMP

50 219107 No6 X 5/8" LONG PLASTITE SCREW

51 229066 RELEASE BUTTON

52 219323 COMPRESSION SPRING

53 219212 M3.5 X 10MM LONG TAPTITE SCREW

54 219568 No8 X 3/4" LONG PLASTITE SCREW

55 220824 A.C. CHARGING LEAD / NEON ASSEMBLY STANDARD SPEC MACHINES

220822 A.C. CHARGING LEAD / NEON ASSEMBLY CSA SPEC MACHINES

56 220592 8 WAY CABLE

57 220591 6 WAY CABLE

58 219047 M5 X 10MM LONG POZI PAN SEMS SCREW

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Numatic TTB 345S in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13,2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Numatic TTB 345S Manual

Product: