Manual Numark TTXUSB turntable (page 9 of 48) (English, German, French, Italian, Spanish)

618180

Zoom out

Zoom in

1/48

Display Controls

The Display of the TTXUSB was developed to instantly provide usable feedback regardless of the turntable

orientation. Understanding its functions may improve your skill level.

1. Platter Direction Sensors: Whether the turntable platter is turning or stopped, these segments

indicate the direction of rotation. They move in pairs on opposite sides of the display.

NOTE: If the platter is removed while the turntable is powered on, the entire ring of

segments will flash indicating that the drive magnets have been pulled apart and the

motor has entered PROTECTION MODE. It is recommended that the turntable be powered

off after it enters PROTECTION MODE before replacing the platter.

2. Multi-Function Segment Indicators: Depending on the display mode, these Indicators may

provide pitch, BPM or motor settings. See the independent functions of the PITCH, BPM and MOTOR

CONTROLS for additional information.

3. BPM Button: Pressing this button will toggle the center section of the display between the current

pitch setting and an estimated beats per minute (BPM) reading. If this button is pressed and held for

2 seconds, the BPM counter will recalculate the BPM estimation. If the display is indicating a steady

"---" this means that the TTXUSB is calculating the BPM range OR it is unable to distinguish an

estimate. If the BPM estimation is a flashing "---" then this indicates that there is no audio being

processed.

4. Pitch versus BPM indicators: The

word PITCH and the PERCENTAGE

symbol are both active while the

display indicates the pitch setting. The

BPM indicator is only active when the

display is set to provide BPM

estimations.

5. Pitch Range Button: This button

toggles the pitch range between 10,

20 and 50% when pressed in

succession. If this button is pressed

and held for 2 seconds, the pitch

range will be set to 8% until the

button is pressed again. If this button

is pressed and held together with the

BPM Button (3), then the contrast of

the Display will be reduced until the

buttons are released.

6. Pitch Range Indicators: Depending

on the pitch range (8, 10, 20, 50%)

these indicators will be active. When

the pitch range is set to 8%, none of

these indicators are active.

7. RPM settings: The 33, 45 or 78

segments will be active for the

respective motor RPM mode.

8. Key Lock Indicator: This symbol

indicates that the onboard digital signal processors are correcting the KEY of the playback source.

NOTE: The KEY LOCK function can only be used while the output is set to LINE level.

9. Quartz Lock Indication: If the QUARTZ LOCK function (General Controls) is engaged, this

segment becomes active and the display will flash "- Q -" if the PITCH FADER is adjusted until the

QUARTZ LOCK function is deactivated.

10. Start Time Indicator: If this indicator is active while the motor is starting, it means that the

startup time has been adjusted using the Start Time Adjuster (General Controls)

11. Brake Time Indicator: If this indicator is active while the motor is stopping, it means that the stop

time has been adjusted using the Braking Time Adjuster (General Controls)

12. Contrast: Press both (3) and (5) simultaneously to cycle through contrast levels on the display.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Numark TTXUSB turntable in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 2,46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Numark TTXUSB turntable Manual

Product: