618122
6
Zoom out
Zoom in
Previous page
1/32
Next page
6
Rear Panel
1. Master Output (RCA): Use standard RCA
cables to connect this output to speakers or an
amplifier system.
2. USB: Sends USB MIDI data to control various
software parameters.
Performance Pad Modes
The upper row of pads has different functions depending on their mode: Manual Loop Mode,
Auto Loop Mode, and Sample Mode.
To select a mode, hold down the Pad Mode button and
press one of the upper pads.
An LED under the pad section indicates the currently selected
mode.
Manual Loop Mode: Hold Pad Mode and press the pad marked Manual Loop (silkscreened
above the pad) to assign the lower 4 pads to the functions listed below:
Loop In Sets the beginning of a loop. After a Loop Out point is set, when this button is
pressed again, it will allow for fine adjustment of the Loop In point.
Loop Out – Sets the end point for the loop. When this button has been pressed after a
Loop Out point has been set, it will allow for fine adjustment of the Loop Out point.
On/Off – When this is pressed inside a loop, this will turn the loop off. When pressed
outside a loop, this will activate the loop and start playback from its Loop In point. If a loop
has not been set, this button will have no effect.
Loop x1/2 – Cuts the currently playing loop in half. Press Shift + Loop x1/2 to double the
length the currently playing loop.
Auto Loop Mode: Hold Pad Mode and press the pad marked Autoloop to assign the lower 4
pads to the functions listed below:
Auto 1 Sets and starts playback of a 1-beat autoloop.
Auto 2 – Sets and starts playback of a 2-beat autoloop.
Auto 4 – Sets and starts playback of a 4-beat autoloop.
Auto 8 – Sets and starts playback of an 8-beat autoloop.
Sample Mode: Hold Pad Mode and press the pad marked Sampler to assign the lower 4
pads to the functions listed below:
Sample 1 – Plays the sample assigned to Sample Pad 1.
Sample 2 – Plays the sample assigned to Sample Pad 2.
Sample 3 – Plays the sample assigned to Sample Pad 3.
Sample 4 – Plays the sample assigned to Sample Pad 4.
Beatmixing with MIXTRACK PRO 3 and Serato DJ intro
Below is an example of how to mix tracks using MIXTRACK PRO 3 and Serato DJ Intro:
1. Load tracks onto the decks of Serato DJ Intro by using the Load 1 and Load 2 buttons
on MIXTRACK PRO 3.
2. Move the crossfader all the way to the left on MIXTRACK PRO 3.
3. Turn the Cue Mix knob all the way to the right to ‘PGM’.
4. Play the track that is loaded on Deck 1.
5. Play the track that is loaded on Deck 2 and match it’s BPM to Deck 1’s track. To match
the BPM, press Deck 2’s Sync button on MIXTRACK PRO 3.
6. Once the BPM is matched, move the crossfader on MIXTRACK PRO 3 to fade between
Deck 1 to Deck 2.
1
2
1
2
3
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Numark Mixtrack Pro 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Numark Mixtrack Pro 3 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 4,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info