Manual Numark M6 USB (page 4 of 24) (English, German, French, Italian, Spanish)

618166

Zoom out

Zoom in

1/24

REAR PANEL FEATURES

5666

10 11 12

1. POWER IN – Use the included power adapter to connect the mixer to a power outlet. While the power

is switched off, plug the power supply into the mixer first, then plug the power supply into a power

outlet.

2. VOLTAGE SELECTOR – This 2-position switch sets the AC input voltage for the speaker. U.S. users

should set this switch to "100-120V" whereas U.K. and most European users will need to set this to

"220-240V".

3. POWER SWITCH – Turns the mixer on and off. Turn on the mixer after all input devices have been

connected and before you turn on amplifiers. Turn off amplifiers before you turn off the mixer.

4. GROUNDING TERMINAL – If using phono-level turntables with a grounding wire, connect the

grounding wire to these terminals. If you experience a low "hum" or "buzz", this could mean that your

turntables are not grounded.

Note: Some turntables have a grounding wire built into the RCA connection and, therefore, nothing

needs to be connected to the grounding terminal.

5. PHONO INPUTS (RCA) – Connect phono-level devices, such as turntables, to these inputs.

6. LINE INPUTS (RCA) – Connect line-level devices, such as CD players, samplers or audio interfaces,

to these inputs.

7. CH3 USB – Outputs the Record mix to your computer for recording purposes or sends incoming audio

from your computer to mixer's Channel 3.

8. MIC 2 INPUT – If you would like to use an additional 1/4" microphone on Channel 4, connect it to this

input. To route the microphone signal to the mix, you will need to flip the Channel 4 Input Selector

switch, located on the top panel, to "Mic".

9. MASTER OUTPUT (BALANCED XLR) – Connect this low-impedance XLR output to a speaker or

amplifier system. The level of this output is controlled with the MASTER FADER on the top panel.

10. MASTER OUTPUT (RCA) – Use standard RCA cables to connect this output to a speaker or amplifier

system. The level of this output is controlled by the MASTER FADER on the top panel.

11. BOOTH OUTPUT (RCA) – Use standard RCA cables to connect this output to a booth monitoring

system. The level of this output is controlled by the Booth knob on the top panel.

12. RECORD OUTPUT (RCA) – Use standard RCA cables to connect this output to a recording device,

such as a CD recorder or tape deck. The level of this output is based upon pre-master levels.

WHAT CONNECTION LEAD DO YOU NEED TO CONNECT TO ONKYO AMPLIFIER Submitted on 10-12-2021 at 13:41
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Numark M6 USB in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 2,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Numark M6 USB Manual

Product: