618162

Numark M2 Manual

6
Zoom out
Zoom in
Previous page
1/24
Next page
6
TOP & FRONT PANEL FEATURES
1. POWER LED – Illuminates
when the mixer is on.
2. MIC GAIN – Adjusts the audio
level of the microphone signal.
3. MIC BASS – Adjusts the low
(bass) frequencies of the
microphone channel.
4. MIC TREBLE – Adjusts the
high (treble) frequencies of the
microphone channel.
Tip: If you experience
feedback when using a
microphone at loud levels, try
turning down the high (treble)
frequencies.
5. CHANNEL GAIN – Adjusts
the channel audio gain level,
pre-fader and pre-EQ.
6. CHANNEL TREBLE – Adjusts
the high (treble) frequencies of
the corresponding channel.
7. CHANNEL MID – Adjusts the
mid-range frequencies of the
corresponding channel.
8. CHANNEL BASS – Adjusts
the low (bass) frequencies of
the corresponding channel.
9. INPUT SELECTOR – Selects
the input source to be routed
to the corresponding channel. Input jacks are located on the rear panel.
10. CHANNEL FADER – Adjusts the audio level sent to the Program mix.
11. CUE GAIN – Adjusts the audio level of the Cue channel in the headphones.
12. HEADPHONES OUTPUT – Connect your ¼” headphones to this output for cueing and mix monitoring.
Headphone output controls are located on the top panel.
13. CUE MODE SELECTOR – Selects the audio to be routed to the headphones. Switch it to “MASTER”
to hear the Program mix. Switch it to “CH1 CH2” to hear Channels 1 and 2 (see #14 above).
14. CUE SLIDER – When CUE MODE SELECTOR is set on “CH1 - CH2” (see #13), the cue slider blends
between Channel 1 & Channel 2 audio in the headphones. Move this slider to the left to hear Channel
1, or to the right to hear Channel 2.
15. CROSSFADER – Blends audio between Channels 1 and 2. Sliding the crossfader to the left plays
Channel 1. Sliding it to the right plays Channel 2.
Note: The crossfader is user-replaceable if it should ever wear out. Simply remove the facepanel, then
remove the screws holding it in position. Replace the fader with a quality authorized replacement from
your local Numark retailer only.
16. CROSSFADER (CF) MODE – Press this button to reverse crossfader assignment of Channels 1 and 2.
17. CROSSFADER (CF) SLOPE – Adjusts the slope of the crossfader curve. Flip switch to the left for a
smooth fade (mixing) or to the right for a sharp cut (scratching).
18. LEVEL INDICATORS – Monitors the audio level of the Program mix (L&R) and the pre-fader audio
levels of Channels 1 and 2 (CUE).
19. MASTER FADER – Adjusts the output volume of the Program mix.
4
3
2
5
6
7
8
9
10
5
6
7
8
9
10
15
14
11
13
1
12
16
17
18
19
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Numark M2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Numark M2 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 5,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info