23472

Numark DM1050 Manual

3
Zoom out
Zoom in
Previous page
1/11
Next page
FRONT PANEL FEATURES
1. Power LED: Illuminates when the mixer is
on.
2. Mic Gain: This knob adjusts the volume of
the microphone input.
3. Mic Treble: This knob adjusts the high-tone
of the microphone.
4. Mic Bass: This knob adjusts the low-tone of
the microphone.
5. Channel Gain: This rotary control adjusts
the pre-fader input level.
6. Channel Treble: This rotary control adjusts
the high-tone level.
7. Channel Middle: This rotary control adjusts
the middle-tone level.
8. Channel Bass: This rotary control adjusts
the low-tone level.
9. Input Selector: This toggles select what
input source is routed to the channel from
the rear panel connected units.
10. Channel Fader: This slide fader is used to
adjust the level sent to program mix.
11. Headphone Volume: This rotary control
adjusts the volume level of the headphone
output.
12. Headphone Jack: Your headphones can be
connected to this ¼” terminal. The volume
should always be set at its lowest setting
while connecting and disconnecting
headphones to prevent damage to
headphones and/or your hearing.
13. Cue Slider: Channels 1 and 2 can be
previewed using this mini-crossfader.
Sliding this to the left plays the left
“channel-1” and sliding to the right plays the
right “channel-2”.
14. Cue Meter: This meter shows the peak,
“PFL”, Pre Fader levels of channels 1 and 2.
You can use the channel “Gain” and “EQ”
controls to match the levels of input signals
while cueing.
15. Master Cue Selector: When selected only
the master output is heard in the
headphones.
16. Replaceable Crossfader: This slide fader
blends audio between the channels assigned
to the left and right assign switches.
Note: This fader is user replaceable if it
should ever wear out. Simply remove the
facepanel and then remove the screws
holding it in position. Replace the fader with
a quality authorized replacement from your
local Numark retailer.
17. Crossfader Direction: Activation of this
switch reverses the assignment of CH-1 and
CH-2 on the crossfader.
18. Crossfader Contour Control: The position
of this control determines how quickly or
intensely the crossfader will blend.
19. Master Output Knob: This rotary control
adjusts the main output volume.
20. Stereo Level Indicator: quickly and
accurately tracks level of audio.
REAR PANEL FEATURES
Note: It is recommended that the mixer be
turned off before connecting and
disconnecting any sources to the inputs of the
mixer.
1. Microphone Input: Microphones with a ¼”
connector can be connected to this input
terminal.
2. Phono Inputs: This input is used for
connecting your turntables through the sensitive
RIAA phono preamplifiers. Only turntables with
phono level output should be attached. Line
level turntables and other devices may be
attached if the Phono/Line rear panel switch is
set to the line position.
3. Phono/Line Source Switch: This switch
activates and deactivates the sensitive RIAA
phono preamplifiers. Only turntables with
phono level output should be assigned
when the switch is in the phono position.
Some turntables offer line level output. To use
these turntables and other line devices like CD
players, switch the input to Line.
4. GND: This screw connector should be used to
secure any turntables or other devices
connected to the mixer that need to be
grounded.
5. Line Inputs: CD players, Tape Decks, Samplers
or other line level input devices should be
connected to these inputs.
6. Record Output: This RCA output is for
connecting a recording device such as a tape
deck or CD recorder. The level of the record
output is based upon pre-master levels.
7. Master Output (RCA): This output is for
connecting an external monitoring device such
as a PA system, powered monitors or a home
stereo. The level of the master stereo output
signal is controlled by the master fader.
8. AC In: This mixer is designed to work with the
power supply assembly that comes with the
unit. While the power is switched off, plug the
power supply into the mixer first, then plug it
into the outlet.
9. Power Switch: Use this switch to turn on the
mixer after all input devices are already
connected to prevent damage to your
equipment. Turn the mixer on before you turn
on amplifiers and turn of amplifiers before you
turn off the mixer.
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Numark DM1050 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Numark DM1050 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info