741659
17
Zoom out
Zoom in
Previous page
1/24
Next page
17
NL
4
Montage van de beugels
Zorg voor een keukenkast zonder bodem. De
kastdeur mag nooit lager zijn dan de onderkant
van de afzuigkap. Voorzie een stopcontact in de
nabijheid van de afzuigkap. De afzuigkap moet ten
allen tijde spanningsloos gemaakt kunnen worden.
Monteer de 2 meegeleverde montagebeugels tegen
de zijkanten van de binnenzijde van de kastwand
met de 10 meegeleverde schroeven (10x 906108).
De onderzijde van de beugel dient op gelijke
hoogte te zijn als de onderzijde van de kastwand.
De voorzijde van de beugel dient gelijk te zijn met
de voorzijde van de kastwand.
5
Bevestigen van de afdichtplaten
Om de achterzijde aan de binnenkant van de kast
af te dichten: Meet de binnenmaat van de kast
(voorzijde van kast tot achterwand).
6
Achterwand van de de kast is 8mm of minder:
Plaats de afdekbeugels totdat die over
eenkomt
met de afmeting die zojuist opgemeten is. Schroef
de vijzen/schroeven (4x 906161) opnieuw vast.
Achterwand van de kast is dikker dan 8mm
of de achterwand zit tegen de muur: Kraak de
achterste lip van de de U-vormige beugel. Duw
het profiel , wanneer het toestel in de kast zit,
tegen de achterwand van de kast en draai de
vijzen/schroeven (4x 906161) opnieuw vast.
DU
4
Montage des Halterungen
Stellen Sie einen Küchenschrank ohne Boden zur
Verfügung. Die Schranktür darf nicht niedriger sein
als die Unterseite der Dunstabzugshaube. In der
Nähe der Dunstabzugshaube muss eine Steckdose
vorhanden sein. Die Dunstabzugshaube muss
jederzeit spannungslos gemacht werden können.
Montieren Sie die 2 mitgelieferten Montagebügel
mit den 10 mitgelieferten Schrauben (10x 906108)
an den Seiten der Innenseite der Schrankwand.
Die Unterseite des Bügels muss auf gleicher Höhe
wie die Unterseite der Schrankwand sein.
Die Vorderseite des Bügels muss auf gleicher
Höhe wie die Vorderseite der Schrankwand sein.
5
Befestigung der Dichtungsplatten
Zur Abdichtung der Rückseite an der Innenseite
des Schranks: Messen Sie das Innenmaß des
Schranks (Vorderseite des Schranks bis Rückwand).
6
Rückwand des Schranks 8 mm oder weniger:
Platzieren Sie die Abdeckbügel so, dass diese mit der
soeben gemessenen Abmessung übereinstimmen.
Ziehen Sie die Schrauben (4x 906161) erneut an.
Rückwand des Schranks ist dicker als 8 mm
oder die Rückwand befindet sich an der Wand:
Brechen Sie die hinterste Lippe von dem U-förmigen
Bügel. Drücken Sie das Profil gegen die Rückwand
des Schranks, wenn sich das Gerät im Schrank
befindet, und ziehen Sie die Schrauben (4x 906161)
erneut an.
FR
4
Montage des supports
Prévoyez une armoire de cuisine sans fond.
La porte de l’armoire ne doit jamais être plus
basse que la face inférieure de la hotte. Prévoyez
une prise près de la hotte. La hotte aspirante
doit pouvoir être débranchée à tout moment de
l’alimentation électrique. Montez les 2 supports
de montage fournis sur les côtés de la paroi
intérieure de l’armoire à l’aide des 10 vis (10x
906108) fournies. La face inférieure du support
doit être à la même hauteur que la face inférieure
de la paroi de l’armoire.
La face avant du support doit être à la même
hauteur que la face avant de la paroi de l’armoire.
5
Attacher les plaques d’étanchéité
Pour obturer l’arrière à l’intérieur de l’armoire :
Mesurez la dimension intérieure de l’armoire (de
l’avant de l’armoire à la paroi arrière).
6
Si la paroi arrière de l’armoire est de 8 mm ou
moins : Placez les fermetures de protection jusqu’à
ce qu’elles correspondent à la taille que vous venez
de mesurer. Resserrez les vis (4x 906161).
Si la paroi arrière de l’armoire est plus épaisse
que 8 mm ou la paroi arrière est contre le mur:
Faites craquer la dernière languette du support en
forme de U. Lorsque l’appareil est dans l’armoire,
poussez le profil contre la paroi arrière de l’armoire
et resserrez les vis (4x 906161).
EN
4
Mounting the brackets
Pr
ovide for a kitchen cupboard with no bottom.
In no case may the cupboard door be lower than
the bottom of the extractor hood. Provide for a
power socket close to the extractor hood. It must
be possible to disconnect the extractor hood at
all times. Fit the 2 mounting brackets supplied
against the sides of the cupboard on the inside,
using the 10 screws (10x 906108) supplied.
The bottom of the bracket must be level with the
bottom of the side panel of the cupboard.
The front of the bracket should be level with the
front of the side panel.
5
Attaching U-shaped brackets
To seal the back panel on the inside of the cupboard:
Measure the inside of the cupboard (front of the
cupboard to the back panel).
6
The back panel of the cupboard is 8mm or
less: Position the U-shaped brackets to match
the measurements just taken. Tighten the screws
(4x 906161) again.
The back panel of the cupboard is thicker than
8mm or the back panel is placed against the
wall: Snap the back lip of the U-shaped bracket.
When the appliance is in the cupboard, push the
profile against the back panel of the cupboard
and tighten the screws (4x 906161) again.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Novy 8770 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Novy 8770 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Novy 8770

Novy 8770 User Manual - English, German, Dutch, French - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info