741744
19
Zoom out
Zoom in
Previous page
1/26
Next page
19
DU
Installation mit Abluftöffung AUFWÄRTS
3
Lösen Sie die Schrauben auf der Motorabdeckung
(8x).
Drehen Sie die Motorabdeckung eine Vierteldrehung
und platzieren Sie die Motorabdeckung wieder
im Motorgehäuse. Schrauben Sie es mit den
acht Schrauben wieder fest.
4
Verbinden Sie den Abluftrohr an einen Anschluss-
stutzen von den Motor mit Aluminiumband oder
einer Schlauchklemme.
W
enn Sie ein festes Rohr verwenden, legen Sie
zuerst das mitgelieferte Dichtugnsband (801006)
auf den Rand des Anschlussstutzens des Motors.
Halten Sie die Abluftleitung so lang, dass
diese nach dem Ausbau wieder ange-
schlossen werden kann.
• Stecken Sie den Stecker in die Steckdose.
Schieben Sie die eingebaute Einheit an den
Kanten in den Ausschnitt, bis Sie ein festes
Einrasten hören.
Die Grundplatte nicht schieben!
Die eingebaute Einheit verbleibt nun aufgehängt
an ihrem Platz.
5
Befestigung der eingebauten Einheit:
Schieben Sie die Strahlerhalterung vorsichtig
nach unten, dann zum Öffnen kippen.
Anschließend die vier Klemmschrauben von Hand
anziehen, um die eingebaute Einheit dauerhaft
zu sichern. Achtung, in der Gipskartonplatte
nicht zu fest anziehen.
• Schließen Sie die Strahlerhalterung wieder
.
EN
Installation with exhaust opening UPWARDS
3
Loosen the screws on the motor cover (8x).
T
urn the motor cover a quarter turn and place
the motor cover back in the motor housing.
Screw it back on again using the 8 screws.
4
Connect the exhaust duct on a connection nozzle
of the motor using aluminium tape or a hose clamp.
If you use a fixed pipe, first place the supplied
draught strip (801006) on the edge of the connection
nozzle of the motor.
Keep the exhaust duct long enough so that
it can be reconnected after disassembly.
• Put the plug into the wall socket.
Push the built-in unit up into the build-in opening
by pushing on the edges until you hear a firm
click.
Do not push on the bottom plate!
The built-in unit unit will now remain suspended
in place.
5
Fixation of the built-in unit:
Carefully slide the spotlight holder downwards,
then tilt it to open it.
Then tighten the 4 clamping scr
ews by hand to
secure the built-in unit permanently. Attention,
do not overt-tighten in plasterboard.
• Close the spotlight holder again.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Novy 826 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Novy 826 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Novy 826

Novy 826 User Manual - English, German, Dutch, French - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info