741764
16
Zoom out
Zoom in
Previous page
1/24
Next page
EN 16
Remove the Monoblock recirculation lter
TheMonoblocklterislocatedonthetopofthehood.
The grille on top of the hood can be opened by pulling it
towardsthewall.TheMonoblocklterislocatedinthe
cutout and you can remove it from there.
Regenerate the Monoblock recirculation lter
• The Monoblock can be regenerated up to 12 times.
This is done in the oven.
• •Placethelterintheovenfor1hourat120°C.Pro-
videsucientfreshairintheroomwheretheoven
has been placed, as smells can be released. Smells
canbereleasedwhenbakingcertainkindsofsh.
In this case it is best to immediately regenerate the
lterintheoven.
Reset the Monoblock recirculation lter
The cooker hood (motor) must be running
Simultaneously press [+] and [–] for 5 sec. until the red
indicatorlampashes3 timesforconrmation.If the
programming is not carried out, the programming is
automatically set after the chimney hood has been
switched on 10 times.
After a reset, the cleaning indication will be set to 200
hours.
Place the Monoblock recirculation lter
ReplacetheMonoblocklteratthetopofthehoodand
close the grille.
Programming en deactivate the recirculation pro-
gram
• Themotormustbeswitchedo.
• Simultaneously press the [+] and the [–] keys on the
hoodfor5secondsuntilthethirdgreenLEDashes
3 times.
4.3 Maintenance of the hood
Pleaseallowthelightstocooldownsucientlybefore
cleaning the hood. Use a soft, wet cloth and a mild
detergent to clean the hood.
Never use aggressive, abrasive detergents or sponges.
Bleach will damage stainless steel.
The stainless steel surfaces can be treated with Novy
Inoxcleaner (906.060) after cleaning.
4.4 Led lighting
Replacing the led lighting
First, remove the power supply from the hood and
allowthelightingtocooldownsuciently.
Opentheglassplateandremovethegreaseltersfrom
the hood. You can reach the 2 LED spotlights at the
bottom of the hood with your hand.
Removing the LED lamp
First disconnect the cable to the LED to be replaced.
Disconnect by means of releasing the lock, by applying
light pressure while at the same time pulling away.
Next, remove the LED to be replaced by making a gen-
tle rotating movement to the left.
Mounting the new LED
Place the new LED light into the locking ring.
Make a rotating movement to the right until the LED
light is locked. Connect the power cable.
4.5 Technical problem
In case of technical problems please contact Novy
Service Department:
• For Belgium: Tel.: 056/36.51.02
• For France: Tel.: 03.20.94.06.62
• For Germany: Tel.: 0511.54.20.771
For all other countries: your local installor or Novy Bel-
gium: +32 (0)56/36.51.02
Please supply us with the model number of your hood.
The model number can be found on the engra-
vedplaquebehindthelter.
You can make a note of the number here:
……………………………
Dimensions: p. 17-19
Electrical scheme: p. 20
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Novy 7859 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Novy 7859 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info