741790
33
Zoom out
Zoom in
Previous page
1/56
Next page
What to do if trouble occurs?
33
GB
7 What to do if trouble occurs?
Interference with and repairs to the appliance by
unquali ed persons are dangerous as they can result
in an electric shock or a short circuit. Do not interfere
with or try to repair the appliance; this could cause injury
to persons and damage to the appliance. Always have
such work done by an expert, e.g. a Customer Service
technician.
Please note
If your appliance is faulty, please check whether you
can rectify the problem yourself by consulting these
instructions for use.
You may be able to rectify some problems yourself.
They are described below.
The fuses blow regularly?
Contact a technical customer service or an electrician!
Does the hob have tears or cracks?
There is a risk of electric shocks if the glass ceramic
hob develops fractures, cracks, tears or damage of
any other kind. Immediately switch o the appliance.
Disconnect the fuse immediately and call Customer
Service.
You can't switch your induction hob on?
Has the wiring system (fuse box) in the house blown
a fuse?
Has the hob been connected to the mains?
Is the childproof lock activated, i.e. does the display
show an “L”?
Are the sensor keys partly covered by a damp cloth,
uid or a metallic object? Please rectify.
Are you using unsuitable cookware? See the section
on Cookware for induction hobs.
The hob or a cooking zone has suddenly switched
o ?
Did you accidentally press the ON/OFF key?
Are the sensor keys partly covered by a damp cloth,
uid or a metallic object? A buzzer will sound brie y.
After a few seconds the appliance will switch o .
Please remove the item located in front of the sensor
keys.
Has the safety cut-o device been activated, i.e. was
a power level operated unchanged beyond a speci c
period of time? See the section on operation time limit.
The pot sign appears?
A cooking zone has been switched on and the hob
is expecting a suitable pot or pan to be placed on
the cooking zone (pan recognition). Only when a pot
has been placed on the cooking zone will power be
supplied.
The pot sign still appears, even though a pot or
pan was placed on the hob?
The cookware is unsuitable for induction cooking or
the pot or pan is too small.
LED display for cooking settings and residual heat
display H does not come on or only partially.
Display defective. Call Customer Service. Risk
of burning, as the temperature warning is not
guaranteed.
The symbol or Er03 will blink and a time-limited
continuous signal will sound.
Food which has boiled over, cookware or other items
are causing the touch control sensor keys to be
consistently operated. Remedy: clean the surface or
remove the item. To delete the symbol press the
same key or switch the hob o and on.
Error code E2 is indicated?
The electronic unit is too hot. Check the installation of
the hob. Make sure that there is su cient ventilation.
See the section on “Protection against overheating”.
Error code E8 is indicated?
Fault on the left or right fan. The suction opening
is blocked or covered or the fan is defect. Check
the installation of the hob. Make sure that there is
su cient ventilation. See the section on “Ventilation”.
Error code U400 is indicated?
The hob has been incorrectly connected. The controls
will switch o after 1s and a continuous signal will
sound. Connect the appliance to the appropriate
power supply.
An error code (ERxx or Ex) is indicated?
The appliance has developed a technical defect.
Please call Customer Service.
Does the hob make noises (clicking or cracking
noises) or can a buzzing sound be heard when the
hob is switched on?
This is design-speci c and has no in uence on quality
and operation.
Does the cooling fan still operate after it has been
switched o ?
This is normal since the electronic unit is being cooled
down.
Is the cookware you are using making noises?
This is due to technical reasons; the induction hob
and the pot are not at risk.
Pulsating cooking?
The induction heating elements can only switch their
power down to a certain power setting. The heating
element will start to clock below this power setting.
This means that the induction heating element will
switch on and then o again at certain intervals
irrespectively of the selected power setting. This
clocking can be heard and will become visible when
you are cooking through bubbles forming on the
bottom of the pan and then disappearing again. This
pulsating cooking is normal at certain power levels
and will not have any negative e ect on the results of
cooking. Remedy: Make sure that pots and pans have
a thick base so that they have good heat retention
and distribution properties. Always close cooking pots
with a suitable lid. A lot of energy is lost when cooking
pots without a lid are used.
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Novy 3784 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Novy 3784 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 0,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info