Manual Novy 3775 (page 34 of 56) (English, German, Dutch)

741789

Zoom out

Zoom in

1/56

Instructions for assembly

8 Instructions for assembly

8.1 Safety instructions for kitchen unit ﬁ tters

• Veneers, adhesives and plastic surfaces of

surrounding furniture must be temperature resistant

(at least 75°C). If the veneers and surfaces are not

suﬃ ciently heat resistant they may become deformed.

• Ensure that all live connections are safely insulated

when installing the hob.

• Cover strips between the wall and the worktop behind

the hob which are made of solid wood are permissible

as long as minimum clearances in accordance with

the installation diagrams are maintained.

• Minimum clearances of the hob cut-out towards the

rear are to be maintained in accordance with the

installation diagram.

• For installation directly next to a tall cupboard, a safety

distance of at least 50 mm must be ensured. The

side surface of the tall cupboard should be ﬁ tted with

heat resistant material. Due to working requirements,

however, the distance should be at least 300 mm.

• The packaging materials (plastic foil, polystyrene,

nails etc.) must be kept out of reach of children as

these parts are potentially dangerous. Small parts can

be swallowed and there is a danger of plastic sheeting

causing suﬀ ocation.

8.2 Ventilation

• The induction hob is ﬁ tted with a fan that switches

on and oﬀ automatically. The fan starts slowly when

the electronic system temperatures exceed a speciﬁ c

limit. When the induction hob is used intensively,

the fan will switch to a greater velocity. Once the

electronic system has cooled down suﬃ ciently,

the fan will reduce its velocity and switch oﬀ again

automatically.

• Clearance between the induction hob and kitchen

furniture or built-in units must provide for suﬃ cient

ventilation of the induction hob.

• If the power level of a cooking zone is automatically

raised or lowered (see section on thermal cut-oﬀ

device) it is likely that the cooling system does not

cool suﬃ ciently. In this case we recommend that

the back wall of the bottom kitchen unit in the area

of the worktop cut-out be opened and that the front

transverse strip of the unit be removed over the

entire width of the appliance in order to promote the

circulation of air.

min. 5 mm

min. 20 mm

min. 5 mm

min. 20 mm

min. 30 mm

In order to better ventilate the hob, an air gap of 5 mm

should be left at the front.

8.3 Installation

Important information

• Remove any transverse strips underneath the worktop

at least in the area of the worktop cut-out.

• The induction hob may not be used when pyrolysis

operation is taking place in a built-in oven.

• When installing the appliance on top of a drawer it

is essential to ensure that no sharp items are stored

in the drawer since these could become bent on the

underside of the hob and prevent the drawer from

being opened and closed.

• If a shelf has been inserted underneath the hob,

there must be a clearance of at least 20 mm to the

underside of the hob in order to ensure that the hob is

suﬃ ciently ventilated.

• The hob may not be installed above refrigerators,

freezers, dishwashers, washing machines or dryers.

• To avoid danger of ﬁ re, make sure that no combustible

objects which could easily catch ﬁ re or become

deformed on exposure to heat are directly next to or

under the surface.

Sealing of the hob

Before installation, correctly insert the sealing unit

delivered with the hob.

• No liquids may penetrate between the edge of the hob

and the worktop or between the hob and the wall and

come into contact with any electrical appliances.

• When installing a hob into an uneven worktop, e.g.

with a ceramic or similar covering (tiles etc.), the seal

on the hob is to be removed and the seal between the

hob and worktop made with plastic sealing materials

(putty).

• The hob must under no circumstances be sealed with

silicone sealant! This would make it impossible to

remove the hob at a later date without damaging it.

Worktop cut-out

Cut out the worktop recess accurately with a good,

straight saw blade or recessing machine. The cut edges

should then be sealed so that no moisture can penetrate.

The area is cut out as illustrated. The glass ceramic hob

must have a level and ﬂ ush bearing. Any distortion may

lead to fracture of the glass panel. Make sure that the

sealing of the hob is properly seated.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Novy 3775 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 0,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Novy 3775 Manual

Product: