709171
7
Zoom out
Zoom in
Previous page
1/49
Next page
Operating instructions
These operating instructions describe the safe and proper
handling of the product. All safety and general instructions
relating to the product and all local accident prevention
regulations and general safety instructions should strictly be
followed.
Instruct all persons who use the gate system in its
proper and safe use.
Keep hand-held transmitters out of reach of
children.
Closely observe all opening and closing
movements of the gate when actuating the drive.
For safety reasons, no persons or objects are
permitted in the movement area of the gate.
Maintenance / inspection
The gate system should be inspected by a
specialist firm before the first start-up and as
needed but at last once every year.
Caution!
The closing force, if set too high, can cause injury
to persons or damage to assets.
Caution!
Installation and start-up only by persons after
technical instruction
Testing the gate system
Before starting installation work, check to make sure that the
drive can be used for the purpose for which you need it
considering the properties and dimensions of the gate (see
specifications).
• The right choice of the best-suited drive ensures proper
operation of the gate and reduces failure.
• (If installed properly) the drive complies with the applicable
safety requirements.
General features
• The NovoSwing electromechanical drive has been developed
for swing wing doors of up to 1.8 meters wing width.
• Gates up to 1.8 meters wing width do not require an electric
lock. The lock position is maintained.
• Emergency release: For manual movement of the gate (in
case of power failure) with a key. The unlock mechanism is
easily accessible at the underside of the drive.
Install the control at a place from where you can see the gate.
PRELIMINARY INSPECTIONS
Complete the following steps before defining the fulcrums:
• Define the point on the wing that is best for installation. If
possible, position the fulcrum at half wing height. If the gate
has no structural sectional bar, weld a holder to the point
suitable for the front fulcrum. This spreads the load on a wide
area.
• Before starting installation proper, make a thorough
inspection of the wings. Inspect the state of the wings and look
for cracks and damage.
Check to make sure that the wings are moving easily
• Check the hinges for ease of movement without play.
Electrical connection
When making the cable connections, observe the
instructions in the manuals of components and
the wiring schematics.
The drives should only be used for the opening
and closing of turning gates. The supplier is not
responsible for damage caused due to any other
use of the specifications in this manual.
Specifications
Max. gate weight 200 kg
Max. wing length 1.8 m
Min. wing length 0.8 m
Max. gate height 2.0 m
Door wing area min 50% wind-
permeable
Supply voltage 230 V + - 10 % 50 Hz
Power consumption 250 W
Operating temperature -20 °C / +60 °C
Thrust 1500 N
Pull 1500 N
Opening and closing time 19 secs.
Stroke 350 mm
Duty cycle 30%
Soft start / stop controlled
Extern 24 VAC fuse 5x20 mm
3,15 AT
Notices
GB
Caution!
If the mains power cable of the device is
damaged or needs replacement, have a skilled
person who has received technical instructions do
this in order to avoid danger.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Novoferm NovoSwing at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Novoferm NovoSwing in the language / languages: English, German as an attachment in your email.

The manual is 7,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info