709129
20
Zoom out
Zoom in
Previous page
1/43
Next page
• Trouble-shooting Guide
Important note: when working on the operator, always pull out the mains plug beforehand!!!
Malfunction Possible causes Remedy
Door does not open / close fully. Door mechanics have altered. Have the door checked.
Door does not open / close fully. Set the forces (menu stages 5 and 6).
Travel limit is incorrectly set. Reset travel limit .
After closing, the door opens again slightly. Door blocks shortly before reaching the closed Remove the obstruction.
position. Reset closed travel limit .
Travel limit is incorrectly set.
Door fails to move although the motor is Operator is not engaged. Re-engage the operator 24c.
running.
Door does not respond on impulse from the Battery in the hand transmitter is flat. Replace battery in the hand transmitter.
hand transmitter - but does respond to push- Aerial not available or not fitted. Plug in / align aerial.
buttons or other impulse generators. No hand transmitter programmed. Programme the hand transmitter ( menu
stage 1).
Door does not respond to impulse from hand See diagnostic display. See diagnostic display.
transmitter nor to other impulse generators.
Insufficient range of hand transmitter. Battery in the hand transmitter is flat. Replace battery in the hand transmitter.
Aerial not available or not fitted. Plug in / align aerial.
On-site screening of the receiving signal. Connect external aerial (accessories).
Toothed belt or operator noisy. Toothed belt dirty. Clean toothed belt.
Tension of toothed belt too high. Spray with silicone.
Detension the toothed belt.
18
18
15
GB
Diagnostic display
During operation, the display provides diagnostic information on any possible faults / malfunctions
Number State Diagnosis / Remedy
_______________________________________________________________________________________________________________________
Operator starts up and “0” goes out. Operator receives a start impulse at the START input or via a receiver,
normal operation.
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
0 displayed during the next opening and closing cycle Operator is carrying out a learning cycle for the force limit.
and then goes out. Caution: During these travel cycles the force is not monitored!
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
0 continues to be displayed.
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
Door neither opens nor closes. STOP A connection is interrupted.
External safety device has been activated (e.g. wicket door).
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
Door no longer closes. STOP B connection is interrupted.
External safety device has been activated (e.g. photocell).
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
Permanent impulse signal at the start input. Door no longer accepts a start impulse. External impulse generator emits a
permanent impulse signal (e.g. button is jammed)
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
An error ocurred in setting the operator. Travel path too long.
Repeat setting procedure (menu stages 3 and 4).
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
Closing edge OSE has been activated. Check closing edge, spiral cable and optics.
F (menu stages 3 and 4)
or wicked door contact has been activated.
__________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
Door neither opens nor closes.
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
Motor has come to a standstil. Motor does not rotate. Call in a specialist company.
_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
V
Top end-of-travel position Open has been reached.
Bottom end-of-travel position Closed has been reached.
Gate end position has not been reached.
Force-learning cycle not completed. Must be repeated.
Too much pressure in the gate's end-of-travel positions. Gate setting required.
Gate setting und learning cycle not correctly finalized. Repeat gate setting in menus 3 & 4 and complete force-learning cycle
subsequently.
ault during learning cycle. Repeat position learning cycle.
Reduce force when approaching the end-of-travel positions.
Emergency release has been activated Operator is released, lock the coupling again 24c.
Check wicket door contact.
Fault during self-test. Disconnect power supply.
acation lock activated, gate does not open. Slide switch at SafeControl / Signal 112 confirmed. Reset required.
Deleting radio codes
Press oval key. Keep key pressed while inserting power plug.
All radio codes stored in the hand-held transmitter are now deleted.
Restoring factory setting
Press Open and Close keys at the same time. Keep keys pressed for approx. 3 sec while inserting
power plug.
The factory setting has been restored.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Novoferm NovoPort LED at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Novoferm NovoPort LED in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 10,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info