Manual Novoferm NovoPort LED (page 17 of 43) (English, German, Dutch, French, Spanish)

709129

Zoom out

Zoom in

1/43

• Installation Instructions

Please read these instructions carefully prior to

installation!

Installation should only be carried out by persons

qualified to do so!

Incorrect installation can put the safety of persons at

risk!

In case of improper installation, the manufacturer’s

guarantee becomes void.

Preparing for installation

1. To connect to the mains, a power point must be

installed on site - the included mains lead is

approx. 1 m long.

2. Check the stability of the door, retighten the

screws and nuts on the door.

3. Check that the door is running smoothly and is

in good working order, lubricate the shafts and

bearings. Check the pretension of the springs

and, if necessary, re-adjust.

4. Dismantle the existing door latches (bolt plate

and catches).

5. For garages without a second entrance, an

emergency release is required (accessory).

6. If a wicket door is included, fit the wicket door

contact.

7. Check the supplied screws and wall plugs to

ensure that these are suitable for the structural

conditions on site.

Required tools

- Drilling machine with 6 mm masonry drill

- Sturdy side cutter

- Wrench, sizes 13, 15 and 17 mm

- Slotted screwdriver, 3 mm wide

- Phillips screwdriver, size 2 x 100 mm

Choosing the installation side

Choose the installation side in accordance with the

structural conditions on site. The standard

installation side is on the right (as viewed from the

inside). For special installation situations

see .

Spray the track with silicone to achieve optimum

running qualities.

Fitting the toothed belt

The top door track is used for installing the drive unit.

Place the toothed belt with prefitted end clamp in the

track (back of toothed belt facing upwards). 2a Slot

end clamp with hook onto vertical formed end piece.

2b To disengage the drive wheel, actuate the lever.

Feed the toothed belt through the drive wheels of the

motor head as shown.

2c Insert drive unit with the drive wheels into the top

track.

2d Inserting the limit stop.

Position the limit stop at a distance ordering height +

50 cm from the frame under the toothed belt.

The limit stop should stop the operator approx. 5 cm

above the desired open position.

Finally, push end of toothed belt through the opening

in the end assembly angle.

Fitting the rear toothed belt fastening

3a Feed the toothed belt through the end assembly

angle and keep it taut.

Slot sleeve halves, as shown in 3b/3c, onto the

toothed belt.

Attach knurled nuts 3d and turn to tension the

toothed belt by hand.

3e Make sure that you do not twist the toothed belt

in the process.

3f If the toothed belt overhangs, it can be

shortened.

Inserting the top track roller

4a + 4b Remove the track roller's extension ring

4c Insert the track roller into the track, adjust and

screw in place in accordance with the figure shown.

Fastening the door bracket

Place the door bracket on the designated drill holes

of the top door leaf section and screw down with 3

self-tapping screws 6.3 x 16.

Inserting the lifting arm

6a Slot the lifting arm onto the bolt of the motor head

and secure with clip.

6b Hold the other side of the lifting arm between the

door bracket and select hole setting (VL setting for

construction years prior to 2006).

6c Push the bolt all the way through and secure with

clip. Connect door to operator.

Sliding block

Slot the sliding block onto the track profile, push into

the rear opening on the motor head and screw down

with screw 4.2 x 13.

Mains lead cable

The back of the control unit includes a chamber 8a,

where, if required, the excess mains lead can be

stowed 8b.

Connecting the coiled cable

9a At the back of the control unit there is a cable

terminal for the two individual wires.

9b Insert red wire on left (1) and green wire on

right (2) into the terminal.

9c Insert plug (3) into designated socket and allow

to engage.

9d Afterwards, feed the cable through labyrinth.

Fastening the control unit

10a Install the control unit onto the side wall. At a

distance of approx. 1m from the door and 1.50m from

the floor, mark the spot for the first plug hole, drill the

hole, insert the plug but do not screw in fully. Place

the control unit with key hole onto the screw head.

10b Align the unit and mark the remaining fixing

holes, drill holes, plug and fasten with screws

4.2 x 32.

Wall clamp

Hold up the coiled cable in a vertical position. The

maximum extension of the horizontally routed cable

may not exceed three times the original length.

Attach the wall clamp at the bend. Hold the clamp

against the wall, mark the spot, drill, plug and screw

to the wall using screw 4.2 x 45.

Connecting plan / aligning the aerial

Instructions: Do not connect any

current-carrying cables, only connect volt-

free push buttons and volt-free relay

outputs.

Where door systems are used by the

public or are impulse-operated out of sight

of the door, a photocell must be installed.

E. Connection for aerial

Route the aerial on the housing exit upwards.

When using an external aerial, the shielding

must be assigned to the adjacent terminal (F, on

right) 12b.

F. Connection for external impulse generator 12b

(accessories, e.g. key switch or digital coder)

G. Input STOP A

Connection for safety devices

(accessories, e.g. wicket door contact).

An interruption at this input end causes the door

to stop during the opening or closing phase or

prevents the operator from starting up in either

direction. Connection for safety devices 12c

(accessories).

H. Input STOP B

An interruption at this input end causes the

operator to automatically change direction

during the closing phase only.

Connection for 2 wire light barrier EXTRA 626

12d (accessories).

Connection for an optical closing edge

protection OSE 12e.

I. Voltage supply 24 V ~

Connection can take a max. load of 100 mA

(do not exceed!).

Connection for 24V signal lamp12f

(accessories). Connection for an external

receiver 12g (accessories).

J. Plug-in base for radio receiver

K. Connection for an external light, protected light

or signal lamp (protection classification II, max.

500W) 12h (accessories).

Lamp shade

13a The lamp shade conceals the terminal

connections. To do this, feed the back part of the

lamp shade underneath the guides of the control

unit.

13b Fasten the lamp shade with two self-tapping

screws 4.2 x 16.

Control elements

14a/b The control elements for programming the

door operator are located behind the white cover.

The cover can be opened with a screwdriver.

Once the operator has been programmed, the cover

is reclosed and serves as an interior push-button 23.

A. The numerical display serves to indicate the

menu stage, the respectively set value and the

error/fault diagnosis.

a. The incremental display, lights up to indicate

readiness for operation and flashes on

acknowledgement of learned hand transmitter

codes.

B. During the setting / adjustment phase button

serves as an "UP" button and outside the menu

as a START button.

C.During the setting / adjustment phase button

serves as a "DOWN" button.

D.Button serves to call up the settings /

adjustment menu, to change the menu stages

and store the settings.

Programming the control unit is menu-driven.

Pressing button , calls up menu prompting. The

numbers displayed indicate the menu stage. After

approx. 2 seconds, the display flashes and the

setting can be altered via buttons and . The

selected setting is stored via button and the

programme automatically jumps to the next menu

stage. By repeatedly pressing the button , menu

stages can be skipped. To quit the menu, repeatedly

press button until "0" is displayed again. Outside

the menu, button can be used to generate a start

impulse.

Menu stage 1: Programming the start

function for the hand transmitter

Briefly press button . “1” is displayed. As soon as

the display flashes, press and keep pressed for

approx. 1 second the button of the hand transmitter,

with which you later wish to start the operator. As

soon as the code has been read, the red point

display (a) flashes five times before quitting.

Further hand transmitters (up to a maximum of 30)

can be programmed.

Menu stage 2: Programming the light

function for the hand transmitter

Figure 0

will be displayed. Menu finished.

Press key briefly and figure 1 will be displayed.

Press key once again and figure 2 will be

Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Novoferm NovoPort LED in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 10,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Novoferm NovoPort LED Manual

Product: