Manual Novoferm NovoPort III Generation (page 19 of 43) (English, German, Dutch, French, Spanish)

709128

Zoom out

Zoom in

1/43

• Operating Instructions

Information regarding the operating instructions

Allpersonsusingthedoorsystemmust

beshownhowtooperateitproperlyand

safely.

- Whentheoperatorisbeingactuated,any

openingandclosingphasesmustbe

monitored.

- Keephandtransmittersoutofthereachof

children.

- Itmustbeensuredthatneitherpersonsnor

objectsarelocatedwithinthedoor'srangeof

travel.

Functionalsequence

Internalsafetydevice

Externalsafetydevices

Quickrelease

22a

22c

These operating instructions describe how to use the

product properly and safely. The safety advice and

instructions as well as the local health and safety

regulations and general safety regulations for the

range of use must be observed.

The garage door operator can be actuated by push-

button on the control unit (figure ) or by other

impulse generators, such as hand transmitters, key

switches etc. It is only necessary to generate a short,

sharp impulse.

- Initial impulse:

Operator starts up and causes the door to travel

to the set OPEN or CLOSE end-of-travel

positions.

- Impulse generated whilst the door is in motion:

Door stops

- A new impulse:

Door continues to move but in the opposite

direction.

If the closing door encounters an obstruction, the

operator stops and causes the door to open to its top

end-of-travel position in order to clear the

obstruction.

During the last 2 seconds of closing, the door only

opens slightly, this being sufficient to clear the

obstruction but otherwise preventing anyone from

being able to see inside the garage.

If the opening door encounters an obstruction, the

operator stops immediately. The door can be closed

again by generating a new impulse.

- Wicket door contact STOP A

An open wicket door stops the operator

immediately or prevents it from starting up.

- Photocell defective (STOP B)

If the photocell is interrupted whilst the door is

closing, the door stops and reverses direction.

An interruption whilst the door is opening has no

effect.

When altering settings or making adjustments, in the

event of a power failure or malfunctions, the door can

be disengaged from the operator by actuating the

pull cord with knob on the lifting arm (figure ), so

that it can be operated manually.

To resume operation of the operator, press the lever

on the motor head (figure ) and the operator re-

engages.

If the door is to be operated manually over a longer

period of time, then the door latches which were

taken out of service for power operation, must be

refitted, otherwise the door will not be latched when

closed.

•

Lighting

Changingthelightbulb

Signal light

Handtransmitters

15 16

Empty batteries must be disposed of separately

(toxic waste)!

The lighting switches on automatically whenever a

start impulse is generated and switches off again

after the set time phase (factory setting approx. 90

seconds).

A second button on the hand transmitter can be

programmed for 4-minutes light (figure ). When

the button on the hand transmitter is pressed, the

light switches on independent of the motor and

switches off again after approx. 4 minutes.

Pull out the mains plug and open the lamp shade

using a Phillips screwdriver size 2 x 100. Replace the

light shade (230 V, 40 W, cap E27) and screw the

lamp cover back on again.

If a signal light for signalling the opening and closing

phases is installed, this flashes together with the

lamp in the operator as soon as a start impulse is

generated. The operator starts with a time delay in

accordance with the set early warning phase (see

Special Settings in menu stage 7).

- Programming further hand transmitters:

See menu stages 1 and 2 (figures and ).

- Changing the battery: slide back the battery

compartment cover on the hand transmitter.

Take out the battery.

- Insert a new battery. Be sure to pole correctly!

Slide the cover back on.

• Further operating modes

•

In menu 9, another operating mode can be chosen.

For the setting applying to menu 9, see parantheses.

Normal operation for ventilation position (1)

Operation on a side-opening sectional door (2)

The ventilation position is designed to allow

ventilation of the garage. For this, the door is opened

approx. 10 cm.

Actuation as for normal operation.

By pressing the 2 button on the hand transmitter or

generating an impulse via another device, the door

can be brought into the ventilation position from any

given position.

The gate will close automatically after 60 min or can

be closed earlier by any impulse transmitter.

Instead of opening the door fully, the door can be

partially opened by approx. 1 m in order to provide

access to the garage.

By pressing the 2 button on the hand transmitter or

generating an impulse via another device, the door

can be brought into the partially open state from any

given position.

• Maintenance/Checks

The operator control unit features a dual-processor

safety system to monitor the force limit.

The integral force cut-out is automatically tested at

each end-of-travel position.

The door system must be checked before initial

operation and at least once a year thereafter, In the

process, the force limiting device (figure ) must be

tested!

CAUTION! If the closing force is set too

high, this can result in injury to persons and

damage to property.

The opening force can be re-adjusted in menu stage

5, the closing force in menu stage 6.

Foryourownsafetywerecommend

that thedoorsystembecheckedbya

specialistafterinitialinstallationand

thenregularlyatintervalsof1year

minimum.

Monitoringtheforcelimit

•

Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!

Je ne parviens pas à déprogrammer mon émetteur même en suivant exactement la notice Submitted on 17-11-2021 at 10:09
Reply Report abuse
On m'a volé un émetteur de porte. Je suis la notice pour effacer la programmation afin d'en faire une nouvelle mais cela ne fonctionne pas. La programmation existante reste active ? Submitted on 17-11-2021 at 10:07
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Novoferm NovoPort III Generation in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 6,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Novoferm NovoPort III Generation Manual

Product: