709108

Novoferm Novomatic 823S B1200 Manual

51
Zoom out
Zoom in
Previous page
1/144
Next page
51
Diagnostic display
B-1200
Diagnostic display
Number State Diagnosis / Remedy
The operator starts up and
“0”goes out.
In normal operation, drive receives start signal via START input or
by drive unit.
Garage door has reached end
position OPEN.
Garage door has reached end
position CLOSE.
End position has not been
reached.
The display shows a “0” during
the next opening and closing
cycle and then goes out.
The operator is carrying out a learning cycle for the force limit.
Caution: During this travel cycle the operator does not monitor the
force. Make sure that no persons or objects are in the travel path
of the garage door.
The display continues to show a
“0”.
The force-learning cycle did not complete and must be repeated.
The door’s end-of-travel position may have too much pressure.
Set the door’s pressure to the correct level.
The door does not open or close. Interruption at STOP A or activation of an external safety device
(such as a pass-door).
The door does not close. Interruption at STOP B or activation of an external safety device
(such as a photoelectric sensor).
The door setting and learning
cycle did not complete correctly.
You must use menu stages 3 and 4 to complete the door settings
correctly and then complete the force-learning cycle.
There is a permanent impulse
signal at the start input.
Start signal is not detected or pulse duration (eg button jammed).
An error occurred in setting the
operator.
The travel path is too long.
Repeat setting procedure with menu stages 3 and 4.
Visual closing edge protection
OSE or electrical contact strip 8k2
has tripped.
Check the connection/wiring.
Error in learning cycle. Repeat position learning cycle with menu stages 3 and 4.
Reduce force when approaching the end-of travel positions.
The door does not open or close. An error occurred during the self-test. Disconnect the power
supply.
Motor standstill. The motor does not rotate. Call a specialist company to repair the
motor.
Electronic brake activated. The
garage light remains on.
The drive is pulled from the upper end position. Check the door
and the springs. Setting upper end lower.
The vacation lock is activated.
The door does not open.
The side switch for SafeControl/Signal 112 is active. A reset is
required.
… 51 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Novoferm Novomatic 823S B1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Novoferm Novomatic 823S B1200 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 6,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info