Manual Novoferm Novomatic 413 (page 15 of 45) (English, German, Dutch, French, Spanish)

709099

Zoom out

Zoom in

1/45

Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!

full lenght.

Push connector (7) centrally over the joint.

Attach central support (13) to track (8) in front of the

connector (7).

Positioning the prefitted operator at an angle to the

door, screw to wall bracket (10). Lift up operator,

making sure that it cannot fall down, and align in such

a way that the track runs horizontal and parallel

between the door tracks.

Establish the length of the support straps for the

operator head and the central support. If necessary,

shorten using a saw, and then screw in place.

Before starting any drilling, cover over track

and operator head to protect them from drilling dust.

Mark fixing points on the ceiling, drill 10 mm holes for

plugs and screw on support straps.

If the toothed belt or chain appear to be too slack,

slight retensioning may be required. It may be

necessary to take up the slack by adjusting the

support straps.

In order to carry out further work, it may be necessary

to disconnect the operator from the door by pulling

the pull cord on carriage (4) and move the door

manually.

If the door is to be operated manually for a

longer period of time, then the locking pin must be

Fasteningthetracktooperatorhead

Fitting the connector attachment

Attaching the wall bracket

Slot track (as illustrated) with chain sprocket (2) onto

the operator shaft (1a) and screw down with the 4

self-tapping screws.

The enclosed door connector attachment is

suitable for all Novoferm up-and-over doors and

Novoferm ISO20 sectional doors.

Position door connector attachment (11) centrally on

the top edge of the door leaf.

Mark fixing holes and drill using 4 mm metal drill

(max. Drilling depth 10 mm) or use the existing drill

holes. Screw on attachment using enclosed self-

tapping screws 6.3 x 16 (4 - 6 screws up-and-over

door, 6 screws - ISO20).

For other sectional doors, use telescopic fitting

(17) (accessory).

In order to ensure that the door can run freely

underneath the track, distance “x” must be greater

than 20 mm. Choose distance “x” so that the angle of

the linking bar does not exceed 45° (see figure 11).

Mark the door’s highest point of travel “a” plus

distance “x” on the lintel.

Hold wall fastening (10) at the total height (”a” + “x”)

vertically over the door connector attachment drill,

drill holes for wall plugs and screw the wall bracket

onto the wall.

Place linking bar (12) between carriage (4) and the

door connector attachment (11) and connect at both

ends with the bolts. Provide bolts with security clips.

Attach security clips to bolts.

Suspendingtheboomfromtheceiling

Support straps

Note:

Connectingthedoorconnectorattachment

tothecarriage

Disengaging the carriage

Note:

• InstallationInstructions

Please read these instructions carefully prior to

installation!

Preparing for installation

The following tools are required

Attention:

Supplypackage=completeset

Overview

Track

Installation should only be carried out by persons

qualified to do so!

Incorrect installation can put the safety of persons at

risk!

In case of improper installation, the manufacturer’s

guarantee becomes void.

1. In order to allow mains connection, a socket

must be available on site - the supplied mains

connecting cable has a length of 80 cm.

2. Check the stability of the door. Retighten the

screws and nuts on the door.

3. Check if the door is running smoothly. Lubricate

shafts and bearings. Check the petension of the

springs and if necessary re-adjust.

4. Establish the door’s highest point of travel (see

figure 6).

5. Close the door and disable any existing locks

out of operation, if necessary dismantle.

Parts of latching devices, which could

form pinch or shear points, have to be

dismantled.

6. For garages without a second entrance, an

emergency release is required (accessory).

7. If a wicket pass door is included, fit the wicket

door contact.

8. Insert the light bulb into the operator and fasten

the lamp cover with 2 screws 4.2 x 50.

- Drilling machine with

10 mm masonry drill

4 mm metal drill

- Metal saw

- Spanner, sizes 10, 13 mm

- Slotted screwdriver, width 3 mm

- Phillips screwdriver, size 2 x 100

- Spirit level

Check the supplied screws and wall

plugs prior to use to ensure that these are suitable for

the strctural conditions on site.

Items 2 - 9 are pre-assembled

1. Operator head including LED-module

2. Driving pinion

3. Track, operator side

4. Carriage

5. Toothed belt or chain

6. Deflection roller

7. Connector

8. Track, door side

9. Tensioner

10. Wall bracket

11. Door connector attachment

12. Linking bar

13. Central support

14. Bag of screws

15. Hand transmitter

16. Support straps

17. Telescopic fitting for sectional doors

(accessory)

Remove the packaging and fold out the track to ist

removed from parking position (a) on the left and with

theopull cord in locking position (b).

In order to relock, return the locking pin into the

parking position (a) on the left and restore the

connection between the operator and the door. On

the next movement, the carriage automatically re-

engages.

connect

potential-free buttons and potential-free

relay outputs. Finally, replace the cover and

screw down.

Before using the operator for the first

time, it must be tested to make sure that it

is working properly and safely (see

section on Maintenance/Checks).

E. Connecting the aerial

F. Connection for external impulse generator

(accessory, e. g. key switch or digital coder) 13b

G.Input STOPA

Abreak at this input end causes the operator to

stop or prevents it from starting up.

Connection for wicket door contact 13c

(accessory)

H.Input STOPB

Abreak at this input end causes the operator to

automatically change direction during the closing

cycle.

Connection for 2-wire photocell EXTRA626 13d

(accessory).

Connection for optical closing edge safety device

OSE 13e (accessory).

I Voltage supply 24 V DC , max. 100 mA

Connection for 24V signal/traffic light 13f

(accessory).

Connection for external receiver 13g.

J. Plug-in base for radio receiver

K. Connection for external lighting (with earth) or

signal light (protection class II, max. 500W) 13h.

In case of increased need for personal safety, in

addition to the operator’s internal force limit, we

recommend installing a one-way photocell. Further

information on our range of accessories can be

found in our sales literature. Consult your specialist

dealer.

1. Pull out the mains plug and disconnect all existing

terminals.

2. Disconnect door and operator.Fix door.

3. Proceed according to points 3 to 13 of the

installaton Instructions but in reverse sequence.

Aligning the aerial / Connecting plan

Note:

Impulse generators and external safety devices

Dismantlingtheoperator

It is essential to pull out the mains plug

before opening the cover!

Do not connect any live leads, only

When using an external aerial, the shielding

must be assigned to the adjacent terminal (F, on

right) 13b.

O.LED-module

•

• Warning sticker

Place the sticker clearly visible on the inner surface

of the door.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Novoferm Novomatic 413 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2,8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Novoferm Novomatic 413 Manual

Product: