Manual Novoferm iso 9-3 (page 13 of 76) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

709192

Zoom out

Zoom in

1/76

The instructions for installation, operating and maintenance must be kept in a safe place as long as the door is in use!

- 4 -

Fold down the pairs of horizontal tracks, unhook the double

steel cables, remove the spring assemblies and unscrew the

horizontal pairs of tracks from the door frame.

Dismount the anchor tracks.

Unscrew the pairs of horizontal tracks from the track connector.

Dismount the rollers and hinges section by section from top to

bottom and remove the corresponding sections from the door.

Secure the door frame so that it cannot fall down. Loosen

the wall and floor screws, remove the door frame from the

opening, lay it on the floor and disassemble (in reverse order to

that described for assembly).

Operating and maintenance instructions for

sectional doorsType iso9-2 / iso20-2 with

extension spring, disassembled version

The door manufacturer accepts no liability if the door is

not operated or serviced correctly and/or if original spare

parts are not used. This also applies to any unauthorised

changes made to the construction of the door.

Operation:

The mechanical mechanisms of this garage door have been

designed to reduce the risk of bruising, cutting and in any way

injuring persons operating or standing near the door. The

following items are essential for the safe operation of the

garage door:

• Before and during door actuation ensure that - apart from

the person operating the door - no other persons or objects

are near any of the moving door parts (e. g. door leaf,

casters etc.).

• The sectional door may only be operated by hand with the

outside handle, the inside handle and, if necessary with the

hand cable. Keep hands away from any moving parts.

• Lock function:

− A full turn of the key enables constant opening and

closing of the sectional door without key.

− A ¾ turn of the key enables the sectional door to be

opened. If the key is turned back a ¾ revolution, the

door is locked.

− By switching the position of the inside locking knob,

the door can be opend and closed without a key.

• The opening area of the door must be kept free of persons

and objects when operating the door from the inside or

outside.

•

••

•

When opening the door, push the door leaf into its end

position and wait until it has come to stop before doing

anything else. The spring tension must be adequate. To

change the spring tension, see Point 30ff.

Attention: Spring tension may only be altered by

qualified fitters!

• This door may only be operated within an ambient

temperature range of - 30° C to + 40° C.

• When closing the sectional door, make sure the retracting

bolt catches securely.

• When fitting this door with a door operator,

− The door installation must comply with all valid EU

directives (machinery directive, low voltage directive,

EMC directive etc.) and all applicable national and

international codes.

− The door installation must be marked correctly with a

nameplate and the CE symbol by the manufacturer

and a declaration of conformity must be issued.

− The documentation given to the customer must be

written in the language of the customer’s country and

must be kept in a safe place for the complete period of

the use of the door.

− The staple plate, the catch mechanism and the

retracting bolt must be dismounted.

It is absolutely obligartory to dismount the hand cable!

Adjustments to the electric operator must only be carried

out by approviately fitters!

Maintenance:

The following points must be checked after mounting the

door and at least every six months thereafter.

Maintenance by unqualified persons or appropriately

qualified fitters:

• Check the door in accordance with the inspection

instructions (Points 26f).

• After installing the sectional door, and after approximately

every 5,000 door movements, lubricate/grease the roller

axles in the roller holders and clean the horizontal tracks

and the spring channels.

• Do not oil the lock cylinder; if it is stiff, use only a light

graphite spray to correct this.

• Make sure there is adequate ventilation for the door frame;

water must be able to run off.

• Protect the sectional door against corrosive and aggressive

substances, such as acids, lyes and de-icing salt.

• Sectional doors with steel fillings are factory-coated with

polyester. Customer painting of the door must be carried

out with a two-component epoxy primer containing solvent

and, after drying, with normal weather-proof paint within

three months of delivery.

•

The door must be re-painted regularly as made necessary

by local weather conditions.

Maintenance by appropriately qualified fitters:

• Check whether screws and clamps are tight and re-tighten

if necessary.

• Check wearing parts (springs, double steel cables etc.)

and, if necessary, replace with original spare parts. To

check the spring assemblies, the spring channel can be

removed without dismounting the horizontal pairs of tracks

by loosening the screws at the front and back of the spring

channel and on the middle suspension bracket.

• Make sure the spring tension is correct. Should it become

necessary to change the spring tension, proceed according

to Point 30ff of the installation instructions.

• Replace the multiple spring assemblies and double steel

cables after about 25,000 door movements (opening and

closing).

This is necessary in the case of:

0 - 5 door movements per day every 14 years

6 - 10 " " 7 years

11 - 20 " " 3.5 years

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Novoferm iso 9-3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,43 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Novoferm iso 9-3

Novoferm iso 9-3 Additional guide - All languages - 18 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Novoferm iso 9-3 Manual

Product: