Manual Novoferm iso 20-2 (page 9 of 90) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

709189

Zoom out

Zoom in

1/90

The instructions for installation, operating and maintenance must be kept in a safe place as long as the door is in use!

- 1 -

Installation instructions for sectional doors type

iso9-2 / iso20-2 with extension spring,

disassembled version

The door manufacturer accepts no liability for incorrect

mounting.

- Mounting should only be carried out by qualified fitters

Please read carefully before mounting

Scope of delivery:

Section package, frame package, panel package

The following items are required for mounting

• the following tools (place inside the garage before

mounting the door if there is no other entrance to the

garage)

folding rule/tape measure, water level, water pump pliers,

reversible ratchet handle with extension and wrench socket

inserts size 7, 10 and 13 ( fork or wrench socket also

possible) fork or open spanner from size 13 for tightening

springs (cf. Item 29), cross-tip screwdrivers size 2 and 3,

slot screwdriver, hammer drill with drill bits, ∅10mm

(drilling depth of at least 65mm), at least 2 screw clamps,

possibly square timber, hammer, metalsaw, small nippers,

chisel and

•

••

•

Mounting material suitable for the building situation. Note:

Check that the wood screws S8 supplied and the plugs

S9 are suitable for the building situation before use.

•

••

•

Important :

•

••

•

The door may only be mounted in a finished opening

and on a finished floor!

• As a precautionary measure, compare the garage

dimensions with the coordinating size of the door before

mounting.

− minimum inside width of garage

= coordinating size –width + 180mm

− minimum garage ceiling height

=coordinating size –height + 120mm (also suffices for

door operators)

− minimum side room right and left = 55mm

• Letter/numeral combinations, e. g. S8

, refer to the

respective mounting and installation materials in the

illustrated section, a successive subscript L or R, e.

g. 1

, indicates a part for the left or right side (observe

markings on parts). The omission of a subscript L or R

indicates a part that can be used either left or right.

Figures in brackets, e. g. [

1.10

], refer to the respective

illustration in the illustrated section.

Mounting of door frame

( 1 ) Lay the angular frames 1

+ 1

on to wood or something

similar (to protect them from scratches) and screw together

the angular frame 1

+ frame panel 3 + angular frame 1

(tapping screws have already been pre-mounted) [

1.10a

( 2 ) Screw the leading plate 4 with S13

on top on the angular

frames 1

+ 1

[

1.10b

( 3 ) Loosely screw the wall anchor 7 to the angular frames

R/L

right and left with S6 + M12 according to the side

room.

( 3a ) Side room 55 - 120mm: Set the wall anchor 7 to the

inside

[

1.10ca

]

( 3b ) Side room more than 120mm: set the wall anchor 7

to the side

[

1.10cb

]

If other mounting materials are used, make sure they

have at least the same load-carrying capacity as the

supplied wall anchor 7.

( 4 ) Set up the door frame behind the opening, secure it so it

cannot fall over, and use the water level to align exactly

parallel and at a right-angle [

1.15

] (also ensure that the

frame panel 3 is level). Centre and clip panel retainers 13

to the upper frame part [

1.15d

]. Finally fasten with S8 + S9

[

1.15a,c,d,e

]. Put the srew S8 in the plastic bush 81 and fix

the foot of the frame

[

1.15b

]

. Note: do not twist or bend the

angular frames 1

R/L

; it might be necessary to fill the

space between frame and masonry with suitable

material before tightening the screws!!!

( 5 ) Screw each of the right 14

and left 14

pair of horizontal

tracks to end piece 16

R/L

[

1.20a

] + upper rope fixation 5

[

1.20a

] + spring channel bracket 8 each front & back

[

1.20b,c

]+ end connection bracket 10

R/L

[

1.20d

] with S6 +

S12.

( 6 ) Stick on foamed rubber 9 on spring channel bracket 8

[

1.20b

], mount spring channel 12 with S6 + S12 and put on

the edge protection 24 on the front [

1.20e,f

( 7 ) Mounting of anchor tracks

( 7a ) If the distance between the wall and the pair of

horizontal tracks 14

R/L

is smaller than 500mm

(internal width of the garage max. coordinating size+

1030mm if door is fitted in the middle) push an

anchor track 27 with connecting brackets 28 right

and left into the track connector 6 and screw the

clamping plate 29 to S6

+ S12 in such a way that the

anchor tracks can still be pulled out

[

1.20a,b

]

( 7b ) If the distance between the wall and the pair of

horizontal tracks is more than 500mm the track

connector 6 can be later fixed to the ceiling (Cf .

Point. 14).

( 8 ) Screw the horizontal pair of tracks 14

R/L

to the end pieces

R/L

with the header bracket S5 + S12 so that later the

door remains raised when lifted up [

1.25c

]. If the distance to

the wall to small than use the hammer head screw S7

[

1.25c

]

( 9 ) Screw the track connector 6 each with S6 + S12 to the end

connection brackets 10

R/L

[

1.25d

( 10 ) Premount springs [

1.30

Place both triple extension spring assemblies 11 with the

plastic sliding elements downwards on the floor of the

garage (with the spring tightening strap pointing to the back

wall of the garage). Screw a deflection pulley cable

assembly 12 with the black side showing upwards to one

of the triple extension spring assemblies 11 with S5

+ S12.

This is the right spring assembly. Both cable ends are

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Novoferm iso 20-2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Novoferm iso 20-2

Novoferm iso 20-2 Additional guide - All languages - 18 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Novoferm iso 20-2 Manual

Product: