wards to one of the triple extension spring assemblies
17
with
S4 +
M1 . This is the right spring assembly. Both
cable ends are pointing to the right inside garage wall.
Screw the other deflection pulley cable assembly
18 with
the red side showing upwards to the other triple extension
spring assembly
17 with
S4 +
M1 . This is the left spring
assembly. Both cable ends are pointing to the left inside
garage wall.
11 Insert the right and left spring assemblies into the right and
left spring channel
12 and hang in the first hole of the
spring tightening strap in the spring hooks on the corner
connection brackets
6
R/L
and secure with spring con-
nectors
19 .
12 Insert the ends of the double steel cables into the mount-
ing-aid bracket
16 . Make sure the double steel cables
are not twisted.
By
12a Placing each of the two cable ends around the front
deflection pulley cable
13 and hooking into the
mounting-aid bracket
16 .
12b Then hook the double cable clamp (clamps two
cables) directly into the mounting-aid bracket
16 .
12c Check once more to ensure the double steel
cables are not twisted.
13 Apply slight initial tension to both spring assemblies. To
tighten the springs, remove the spring connection
19 , pull
the spring tightening strap to the back making sure it
catches securely in the corresponding hole and replace the
spring connection
19 .
14 Lift up the pairs of horizontal tracks
5
R/L
and secure them
against falling down (Make sure the track connector
3
is safely supported). Also make sure that the cable
clamps of the double steel cables remain in the mount-
ing-aid bracket
16 .
15 Level out the track connectors
3 and the pairs of horizontal
tracks
5
R/L
using a water level and loosely screw to the
wall/ceiling.
15a Ceiling mounting: anchor tracks
14 + clamping
plate
15 + connecting brackets
20 +
S1 +
M1 +
S2 +
D1 .
15b Wall mounting: connecting brackets
20 +
S1 +
M1 +
S2 +
D1 .
16 Screw track bends
21 with
S5 +
M1 to the angular frame
1
R/L
and with
S1 +
M1 to the front suspension brackets
10 (make sure the transition between the track profiles
is straight).
Fasten track connectors
3 and the pairs of horizontal
tracks
5
R/L
completely.
17 Screw both upper cable mounts
22 through the header
bracket with
S6 into the corner piece
11
R/L
. Tighten
M1
on the lower corner piece
11
R/L
pull out the double steel
cables from the mounting-aid bracket
16 . (Warning; the
cable is under slight initial tension) and hook into the
upper cable mount
22 . Be careful not to twist the double
steel cables!!
Mounting of door leaf (top section is positioned in the section
packet on top)
18 Floor section
18a Screw the aluminium floor profile
23 with
S7 to the
floor section (leave the outer holes free) and insert
rubber stoppers
24
R/L
.
18b Right and left on the upper floor section, screw a side
hinge
25 and a middle hinge
26 (two middle hinges
from from coordinating widths of > 2500) each with
two
S7 to the floor section.
18c Place the floor section between the angular frames
1
R/L
and put a 3 cm-thick piece of wood (or some-
thing similar) underneath it so that later the door can
be lifted. Secure the floor section so that it cannot fall
over.
18d Place a roller with a long axis
27 into a left and right
roller holder
28
R/L
, insert into the vertical tracks and
screw to the side hinges
25 with
S1 +
M1 .
18e Place two shims
U1 each on the axles of two rollers
with short axles
29 , place in the lower roller holders
30 (zinc diecastings) and screw the roller holders with
S4 +
M1 to the lower cable mounts
31
R/L
. Screw the
lower cable mounts
31
R/L
to the floor section right
and left with four
S7 each.
19 Lock section
19a Screw side guide plate
36 with
S7 into the right top-
most side hole to the lock section.
19b Press clip into the matching recess on the outside
handle
40 with the long square neck.
19c Insert the lock section into the angular frame
1
R/L
making sure it cannot fall over. Screw with two
S7
each to the side hinges
25 + middle hinge/s
26 to the
floor section.
19d Mount side hinges
25 with long rollers
27 and roller
holders
28
R/L
and middle hinge/s
26 . Compare with
18b / 18d.
19e Mount the lock set to the lock section: Lock plate
38
+ lock set
39 (+ distance frame
33 with iso 9) + out-
side handle
40 + inside handle
35 :
Insert the handle plate to the cover plate
38 from the
outside into the rectangular hole of the lock section
and screw to the lock set
39 (with iso 9: clamp dis-
tance frame
33 in between) from the inside using two
S11. Insert the outside handle
40 through the square
hole of the cover plate
38 (right-angle bend pointing
up) and screw to the inside handle from the inside
35
using
S9 . Note: the lever arm (zinc diecasting) must
point upwards to the right.
19f For doors without door operators (otherwise proceed
to Point 20) insert
S10 from behind into the square
hole in the catch mechanism
37 . Secure temporarily
with
M2 to prevent it from falling out. Screw the catch
mechanism
37 with two
S7 right and left of the lock
section in the pre-drilled holes.
20 Middle section(s)
Screw middle sections analogously to floor/lock section
with hinges
25 +
26 , insert into the angular frame
1
R/L
and
mount the rollers
27 + roller holders
28
R/L
.
21 Top section
Screw the upper roller blocks
44
R/L
on the left/right of the
top section with three
S7 . Insert the top section into the
angular frame
1
R/L
insert the upper roller holders with
rollers
45
R/L
in the upper horizontal track on the right/left
and screw with
S4 +
M1 to the upper roller blocks
44
R/L
.
22 Lift the door leaf and push into its final position. Secure the
door leaf so that it cannot fall down.
Pull the two single cable ends from the mounting-aid
bracket
16 (Warning: the cable can be under slight ini-
tial tension), hook them into the lower cable rocker on the
lower cable mount
31
R/L
and clamp with security plug.
Do not twist the double steel cables!!
●●
22a –
●●
22c
23 Hook retracting bolts
41 +
42 with retracting bolt guidance
43 to the lever arm (straight retracting bolt
41 on the right,
bent retracting bolt
42 on the left).
GB
-7- The instructions for installation, operating and maintenance must be kept in a safe place as long as the door is in use!
