69783
16
Zoom out
Zoom in
Previous page
1/36
Next page
16
pour it into the main wash compartment
and, if you wish to carry out a programme with
the prewash phase, pour it into the
compartment marked .
If required, pour fabric softener into the
compartment marked (the amount used
must not exceed the «MAX» mark in the
drawer). Close the drawer gently.
Select the required programme by means of
the programme selector dial (1)
Turn the programme selector dial to the
required programme. The green light of button
8 starts blinking.
It can be turned either clockwise or
anticlockwise. On position «O» the programme
is reset and the machine is switched OFF.
At the end of the programme the selector
dial must be turned to position «O», to
switch the machine off.
IMPORTANT!
If you turn the programme selector dial to
another programme when the machine is
working, the red light will of the button
8 blinks
3 times and the message Err is displayed on
the display to indicate a wrong selection. The
machine will not perform the new selected
programme.
Select the spin speed or the Rinse Hold
option by pressing button
2
The relevant light will light up.
When selecting a programme, the light
corresponding to the maximum speed allowed
for that programme will illuminate (refer to the
section «Programme table» for the maximum
allowed spin speed).
Select the desired option by means of
buttons
5 and 6
Depending on the programme, different
functions can be combined. These must be
selected after choosing the desired programme
and before depressing the button 8. The
corrisponding light illuminates.
For more information about the compatibility of
the options with the washing programmes,
refer to the section «Programme table».
Select the delayed start by pressing the
button
10
Press this button to select the required delay.
The selected delay time value will appear on
the display for few seconds, then the duration
of the programme will appear again.
You must select this option after you have set
the programme and before you press the
button
8.
You can cancel the delay time at any moment,
before you press button
8.
If you have already pressed it, and you wish
to cancel the delay time, proceed as follows:
set the washing machine to PAUSE by
pressing button
8;
press the button
10 once. On the display will
appear the symbol «0’».
press button
8 again to start the programme.
IMPORTANT!
If the programme has already started, the
selected delay can be modified only after you
have turned the programme selector dial to
the «O» position and after you have selected
the programme again.
The door will be locked throughout the delay
time. If you need to open the door, you must
first set the washer dryer to PAUSE by
pressing button
8. After you have closed the
door, press the same button again.
Note!
The Delay Start cannot be selected with
«Drain» programme.
132966720_GB.qxd 29/05/2009 11.34 Page 16
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nordland WD 8126 EL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nordland WD 8126 EL in the language / languages: English as an attachment in your email.

The manual is 2,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nordland WD 8126 EL

Nordland WD 8126 EL User Manual - Dutch - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info