1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
2. Use the treadmill only as described in this
manual.
3. Place the treadmill on a level surface, with at
least 2 meters of clearance behind it. Do not
place the treadmill on any surface that blocks
air openings. To protect the floor or carpet
from damage, place a mat under the treadmill.
4. When choosing a location for the treadmill,
make sure that the location and position per-
mit access to a plug.
5. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Keep children under the age of 12 and pets
away from the treadmill at all times.
8. The treadmill should not be used by persons
weighing more than 115 kgs.
9. Never allow more than one person on the
treadmill at a time.
10. Wear appropriate exercise clothing when
using the treadmill. Do not wear loose cloth-
ing that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
11. When connecting the power cord (see page 8),
plug the power cord into an earthed circuit.
When replacing the fuse, an ASTA approved
BS1362 type should be fitted to the fuse car-
rier. A 13 amp fuse should be used. No other
appliance should be on the same circuit.
12. If an extension cord is needed, use only a 3-
conductor, 1mm
2
(14 gauge) cord that is no
longer than 1.5 meters.
13. Keep the power cord and the surge protector
away from heated surfaces.
14. Never move the walking belt whilst the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 5 if the tread-
mill is not working properly.)
15. Never start the treadmill whilst you are stand-
ing on the walking belt. Always hold the
handrails whilst using the treadmill.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
17. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
18. Never leave the treadmill unattended whilst it
is running. Always remove the key, unplug
the power cord and move the on/off switch to
the off position when the treadmill is not in
use. (See the drawing on page 5 for the loca-
tion of the on/off switch.)
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 22.) You
must be able to safely lift 20 kg in order to
raise, lower, or move the treadmill.
20. Do not change the incline of the treadmill by
placing objects under the treadmill.
WARNING:To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
IMPORTANT PRECAUTIONS
26
3
PART LIST—Model No. NETL09900 R0800A
To locate the parts listed below, refer to the EXPLODED DRAWING attached in the centre of this manual.
Key No. Qty. Description Key No. Qty. Description
1 2 Foot Rail Insert
2 2 Foot Rail
3 2 Foot Rail Cap Screw
4 1 Left Fait Rail Cap
5 2 Frame Pivot Bolt
6 2 Frame Pivot Spacer
7 1 Magnet
8 1 Front Roller/Pulley
9 8 Frame Pivot Nut
10 1 Reed Switch/Sensor Wire
11 4 U-Nut
12 1 Reed Switch Clip
13 1 Lift Frame
14 4 Star Washer
15* 1 Motor Assembly
16 1 Motor
17 1 Pulley/Flywheel/Fan
18 1 Motor Belt
19 1 Motor Pivot Nut
20 1 Motor Controller Wire
21 1 Motor Tension Bolt
22 1 Motor Pivot Bolt
23 1 Hood
24 2 Incline Motor Bolt
25 4 Plastic Stand-Off
26 1 Power Board w/Clips
27 4 Electronics Screw
28 1 Choke
29 1 Controller
30 1 Electronics Plate
31 1 8” Wire Harness
32 1 Front Roller Adj. Bolt
33 2 2” Console Screw
34 3 Roller Washer
35 1 Front Roller Nut
36 1 Incline Motor
37 1 Incline Motor Stop
38 1 Belly Pan
39 2 Belly Pan Screw (Long)
40 2 Static Decal
41 1 Circuit Breaker
42 1 Receptacle
43 1 On/Off Switch
44 1 Left Endcap Insert
45 4 Belt Guide Screw
46 1 Belt Guide
47 4 Isolator
48 1 40” Reed Switch Wire
49 16 Fastener
50 1 Belly Pan
51 1 Right Foot Rail Cap
52 1 Walking Platform
53 6 Platform Screw
54 4 Rear Platform Screw
55 2 Rear Isolator
56 14 Ground Screw/ Controller Screw
57 1 Ground Wire
58 1 Rear Endcap
59 2 Rear Roller Adj. Bolt
60 1 Latch Warning Decal
61 1 Allen Wrench
62 1 Rear Roller
63** 1 Optional Chest Pulse Strap
64** 1 Optional Chest Pulse
65 2 Handrail Spacer
66 1 Handrail
67 2 Endcap Clip
68 1 Lock Knob
69 1 Upright
70 1 Lock Knob Sleeve
71 1 Spring
72 1 Lock Pin Collar
73 1 Pin Clip
74 1 Lock Pin
75 4 Handrail Bushing
76 1 Pulse Grip
77 4 Handrail Washer
78 4 Handrail Bolt
79 2 Upright Endcap
80* 1 Latch Assembly
81 1 Console Base
82 1 Console
83 2 Console Screw/Belly Pan Screw
84 1 Key/Clip
85 1 15’ iFIT.com Wire
86 1 Jack
87 2 Handrail Endcap
88 1 Console Back
89 1 Releaseable Tie
90 10 1” Console Screw
91 3 Cable Tie Clamp
92 5 8” Cable Tie
93 2 Lift Pivot Bolt
94 2 Wheel Bolt
95 2 Wheel
96 1 Right Endcap Insert
97 3 Grommet
98 1 Upright Wire Harness
99 4 Base Pad
100 13 Screw
101 1 Motor Washer
102 2 Extension Leg
