801561
10
Zoom out
Zoom in
Previous page
1/12
Next page
During the operation of the PulseDive, the Green LED blinks once when you
press any button. It lights up solid when the buttons are pressed down and
held.
POWER ON-OFF
Press the on-off button once to turn the device on. A beep will be heard and
the LEDs will light up according to the battery life status. To turn the device
off, press and hold the on-off button. Double beeps will be heard, regardless
of the mode used, and both LEDs will light up simultaneously.
The device automatically retunes itself when it is turned on. Therefore, keep the
device away from metal objects while powering it on. If you are going to use the
device on wet beach sand or on highly mineralized ground, it is recommended to
turn the device on by placing the search coil on the ground or to turn the device
and retune it over the ground. Although this results in a slight loss of depth, it
provides a more stable operation.
You can also retune your device instantly when the device emits false signals.
In order to retune the device, press the on-off button once. Do not retune the
device over metal objects. Otherwise, the device will experience loss of depth.
When the device is turned off and on, it will start with the last saved settings.
DETECTION MODES
The device has 3 detection modes: Audio, vibration, audio and vibration.
Press the (F) button to change the mode.
Red LED
In addition to the above detection modes, PulseDive also has a red LED that
indicates metal detection.
When the red LED is activated, it flashes once upon metal detection regardless
of the mode used. As you get closer to the target, it flashes faster and more
frequently.
To turn on / off the red LED, press and hold the adjustment button (A).
SENSITIVITY
There are 5 levels of sensitivity. To adjust the sensitivity, press the adjustment
button (A) while holding the function button (F) pressed down. Each time you
press the A button, the sensitivity increases 1 level. Each level is indicated by a
number of beeps and/or vibrations depending on the mode used. For example
level 4 is indicated by 4 beeps and/or vibrations. At maximum sensitivity -level
5- the device emits a long beep and/or vibration. If the red LED is active, it lights
up solid.
Inside highly mineralized holes, the device may produce false signals. In such a
case, reduce the sensitivity.
LED FLASHLIGHT
To activate flashlight, press the adjustment button (A) once while the device is
on. Press it again to turn off.
DIVE MODE
If you are diving with the PulseDive, you need to switch the device to dive
mode in order to prevent the buttons from being pressed by water pressure.
While in the dive mode, the buttons are locked and do not work. Therefore,
make sure that the device is set to the desired settings before switching to
dive mode. Recommended settings are vibration and the red LED to be on.
Hold the device upside down (LEDs facing down) as shown in the picture and
press the (A) and (F) button simultaneously. The green LED will light up and a
beep will be heard and/or the device will vibrate depending on the mode used.
If the red LED is on, it will also blink once.
In dive mode, the device will not detect any targets while you hold it upside
down. It will detect targets when you flip and hold it the right way.
Repeat the steps above to exit the dive mode. When exiting the dive mode, only
a beep will be heard and/or the device will vibrate depending on the mode used;
the green LED will not light up. If the red LED is on, it will also blink once.
IMPORTANT! The PulseDive will not switch to dive mode while detecting metal!
NOTE: The wireless headphones will not work if the device is switched to dive
mode while it is connected the wireless headphones. The wireless headphones
will connect automatically once the device exits the dive mode.
8
OPERATION OF THE DEVICE
IMPORTANT! The PulseDive comes with 2 battery compartment covers. While
using the device in dive mode, use the battery compartment cover that comes
attached to the device and while using the device on land, use the one that
is designed for land use to obtain a louder volume. The cover for land use is
waterproof and can be washed. However, it cannot be used for diving. To prevent
the filter, which is used on the cover for land use, from any damage, do not
insert any sharp objects into the holes for cleaning or any other purposes.
LOST ALARM
The PulseDive has a lost alarm feature which makes it easier to find the device
in case you lose it. If no button is pressed and/or if the device does not detect
any targets for 5 minutes, the lost alarm is activated. The device starts emitting
beeps at short intervals and the LED flashlight starts flashing.
When the lost alarm gets activated while the device is connected to the
wireless headphones, the audio is heard through the device and not through
the headphones anymore.
FREQUENCY SHIFT
It is used to prevent the device from interfering with other detectors nearby.
To shift the frequency, press the on-off button while holding the (F) button
pressed down. Each time you press the on-off button, a beep will be heard
and/or the device will vibrate and the frequency will shift 1 step. There are 40
steps in frequency shift. The central frequency, which is the factory default,
is indicated by double beeps / vibrations.
WIRELESS HEADPHONES CONNECTION
PulseDive has an internal wireless connection module for wireless headphones use.
To activate the wireless connection, turn the device on while holding the (F)
button pressed. The green LED will start flashing at certain intervals to indicate
that the wireless module is on.
To turn the wireless connection off, power off the device while holding the (F)
button pressed.
The pairing instructions can be found in the Nokta 2.4GHz Wireless Headphones
which are sold separately.
IMPORTANT! If the wireless connection is on but the device is not connected to
the wireless headphones, the device will do a channel search and the the green
LED will light up for almost 5 seconds at start up. During this period, the device
will NOT detect metal!
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nokta PulseDive 2-in-1 Set at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nokta PulseDive 2-in-1 Set in the language / languages: English as an attachment in your email.

The manual is 1.62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nokta PulseDive 2-in-1 Set

Nokta PulseDive 2-in-1 Set User Manual - German - 12 pages

Nokta PulseDive 2-in-1 Set User Manual - Dutch - 12 pages

Nokta PulseDive 2-in-1 Set User Manual - French - 12 pages

Nokta PulseDive 2-in-1 Set User Manual - Turkish - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info