Manual Nokta Makro Invenio (page 25 of 36) (English)

801544

Zoom out

Zoom in

1/36

DETECTION SCREENS

HEDEF ID

measurement plays an important role for the device to eliminate the

false signals produced by these rocks.

Magnetic Mineralization Indicator will be displayed on screen in all

modes except for the Ground Anomaly & Cavity mode. You can remove

it by pressing the INFO button. It will come back on screen when you

press the INFO button again.

(3) Ground Balance Window

The ground balance window is divided into 2 parts: The top part shows

the instant ground balance value changes while searching and the

bottom part shows the adjusted ground balance value.

Ground Balance window will be displayed on screen in all modes except

for the Ground Anomaly & Cavity mode. You can remove it by pressing

the INFO button. It will come back on screen when you press the INFO

button again.

To learn how to ground balance the INVENIO, please read the section

titled ''Ground Balance''.

(4) Height Indicator

Shows the height of the search coil on the bar, in centimeters or inches.

The ideal search height for the type of search coil attached, is indicated

with green color. If you hold the search coil at a different height than

the recommended one, this will be indicated by red color on the bar.

(5) Depth Indicator

Shows the depth of the detected target, in centimeters or inches.

It ranges between 0 to 150+ (0-60+ in inches). In other words, for

depths greater than 150cms (60'')., it will show 150+ (60+ in inches).

Upon target detection, the bar will rise and the target depth will be

indicated numerically. Depth reading may vary based on target size

and orientation, metal type and ground conditions.

IMPORTANT! To see the target depth instantly in non-motion modes,

you need to swing the search coil more slowly.

(6) Drift - Metal bar

This bar is present only in the Basic and Expert modes.

All signals obtained by the device, as well as drifts, while searching, are

shown on this bar.

Changes in the ground and temperature, as well as environmental noise,

may lead to negative and positive drifts. During negative drifts, the bar

will fill up in the DRIFT direction, in proportion to the strength of the

drift.

When the device detects a metal or a positive hot rock or if a positive

drift occurs, the bar this time will fill up in the METAL direction, again

in proportion to the strength of the signal or the drift.

(7) Zoom

It is used to magnify or reduce target signal graphs. By using this

feature, you can magnify smaller signal graphs and reduce the larger

ones to better examine them.

If you wish, you can change the zoom scale with the up and down

buttons.

(8) 3D Detection Ground

During searching you can observe the following on the 3D detection

ground :

* All movements of the search coil - left, right, up and down,

* The total scanned area,

INVENIO has 2 detection screens: One with, and one without the

IPTU sensor. The screen with the sensor, will only function fully, when

the IPTU sensor is attached to the device, and it is turned on. If the

detection screen with the sensor is used while the sensor is not

turned on, the device will detect targets and provide their IDs, however

the advanced features (explained further in the manual) will not work.

The detection screen without the IPTU sensor on the other hand, can

always be used, regardless of whether the sensor is attached or not.

All modes, except for the Ground Anomaly & Cavity, will work in

both screens. The Ground Anomaly & Cavity mode will work in the

detection screen with the sensor only. Detection screen selection

does not have direct effect on the operation of the modes. The main

difference between the 2 screens is as follows: When searching in the

detection screen without the IPTU sensor, the device detects targets

and displays their IDs only. On the other hand, while searching in the

detection screen with the IPTU sensor, apart from the IDs, the device

also provides the instant depth, shape and 3D graphs of detected

targets.

DETECTION SCREEN WITH IPTU SENSOR

(1) Target ID Scale

Ranging from 0 to 99, this scale indicates which metal group the ID of

the detected target falls in. Each metal group is indicated by a different

color. For example, negative hot rocks and soil are shown by white

and brown colors, ferrous metals, such as iron, by red, and gold and

non-ferrous metals are indicated by yellow and green colors. When a

target is detected, the cursor will point to the target ID on the scale.

The IDs filtered by Discrimination and Notch Filter settings are shown

in black color on this scale. For more information please read the

sections about Target ID and Notch Filter.

(2) Magnetic Mineralization Indicator

Magnetic Mineralization Indicator ranges from 0 to 99. Upon start up,

the indicator will be empty and 0 will be displayed inside. Based on

the level of magnetic mineralization, this chart will fill up yellow and

the mineralization level will also be indicated numerically inside the

chart.

This measurement can be summarized as the level of magnetic

property and intensity of the ground. Simply, if you are working in an

area which contains intense and magnetized minerals, the level will

be high. If you are working on a less intense ground, the level will be

low.

This measurement is important from two aspects. First, on grounds

with high magnetic mineralization, search depth is low and users

should be aware of this fact. Second, magnetic mineralization is a

property which is particularly seen with mineralized rocks and this

* The length and width of the scanned area by zooming in and out on

ground image,

* The 3D graphs of all target signals with target separation according

to metal groups.

In addition, this advanced detection ground allows you to track back

your scan within a certain period of time and see the detected targets.

DETECTION SCREEN WITHOUT IPTU SENSOR

The functions of the target ID scale, the magnetic mineralization

indicator, the ground balance window, and the Drift-Metal bar are

the same as those in the detection screen with the IPTU sensor. For

this reason, these are not explained again in this section. If you wish,

please read the section above titled ''Detection Screen with IPTU

Sensor''.

(1) Target ID Indicator

Upon target detection, the ID will be displayed here. It ranges from 00

to 99 and gives an idea to the user about what the target may be.

For more details on target ID, please read the relevant section of the

manual.

(2) Target Detection Screen

While searching, the signals, as well as the signal strengths of metals,

positive rocks, and positive drifts can be observed in this section.

The target signals are defined by different colors just like in the color

ID scale. Ferrous metals are shown in red, and non-ferrous metals are

with yellow and green colors. The signals of target IDs discriminated

out by Discrimination and Notch Filter settings are indicated with gray

color.

4 7 86 5

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Nokta Makro Invenio in the language / languages: English as an attachment in your email.

The manual is 5.71 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nokta Makro Invenio

Nokta Makro Invenio User Manual - Turkish - 36 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Nokta Makro Invenio Manual

Product: