801544
12
Zoom out
Zoom in
Previous page
1/36
Next page
This is the information bar located at the bottom of the screen. To see
the info bar, just press the INFO button. It hides automatically or by
pressing the INFO button again. If there is a warning in the message
section, the INFO bar will reappear after a certain period of time.
We can view the INFO bar in 3 sections as below :
Left Side
It shows which command buttons can be used on each screen or menu
(Back/OK/Directional Buttons/CLR/Scan). Active ones will appear green,
inactive ones will appear red.
Middle Section
Shows the mode, operating frequency and warning messages.
Messages that may appear are as follows :
Overload
It appears on screen simultaneously with the overload alarm. This
happens when the search coil encounters a near surface or a very
large object. The device reverts back to normal operation if you lift
the coil up. If the alarm and the message continue along a long line,
you may be over a long metal such as a pipe.
In case of high mineralization, the device may overload. If the cause of
overloading is not a large metal, it may be the ground itself and this
situation may be overcome by lowering the sensitivity.
Coil is disconnected!
It indicates an interruption in the search coil transmitter signal. The
search coil connector may be unattached, loose or disconnected. If
you own another detector with the same coil connector, please be
sure that you have not attached the wrong coil by mistake. If none
of the above exists, the search coil or its cable may have a defect. If
the issue continues when you change the search coil, there may be
an issue in the coil control circuit.
WiFi is off
It will come on screen when there is no wireless connection between
the system box and shaft & handle. In such a case, first check whether
the shaft & handle is on or not. If it is on, try changing the WiFi channel.
For this, press the OPTIONS button, select ''Wireless Shaft Channel'' and
search the channels.
Shaft is not connected!
It comes up on screen when the Wireless Shaft Channel is switched to
off position.
Refresh GB!
This message will appear under the following situations: When the
operating frequency is changed (only in INVENIO Pro), when the
sensitivity level is changed or when the mode settings are restored
to factory defaults. It indicates that you should re-ground balance
the device. Once you ground balance, the message disappears.
Calibrate the sensor!
It comes up on screen at initial start up or when you switch to the
detection screen with the IPTU sensor. For the calibration process,
press the SETTINGS button and select ''Calibrate the sensor''. For
more details, please read the relevant sections of the manual.
Pump the coil!
This message appears when the trigger is pushed forward for
automatic ground balancing. It does not indicate any error or problem.
It only indicates what should be done.
Right Side
This section shows the status of some of the hardware features of the
device.
Indicates the status of the wireless connection between the
system box and shaft & handle. Green means connected,
red means disconnected.
If the optional wireless headphones are connected, the
headphone icon will appear. Otherwise, the speaker icon
will show. If the volume is turned off, the icons will turn
from green to red.
Indicates whether the vibration is on or off. If it is green,
vibration is on. If it is red, vibration if off.
In the SETTINGS or ARCHIVES screen, it indicates the
detection of an external USB drive.
Battery icon number 1 shows the battery life status of the
system box and battery icon number 2 shows the battery
life status of the shaft & handle ( only when the shaft &
handle is on).
When the system box battery is dead, the countdown
numbers before the system shuts down, are shown here.
9
INFO BAR
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nokta Makro Invenio at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nokta Makro Invenio in the language / languages: English as an attachment in your email.

The manual is 5.71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nokta Makro Invenio

Nokta Makro Invenio User Manual - Turkish - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info