296277
6
Zoom out
Zoom in
Previous page
1/56
Next page
Model 9000/9100/9500
6
General and Commercial Installation Checklist
1. Place the softener tank where you want to install the unit.
NOTE:
Be sure the tank is level and on a firm base.
2. During cold weather it is recommended that the installer warm the valve to room temperature before operating.
3. Perform all plumbing according to local plumbing codes.
Use a 1/2" minimum pipe size for the drain.
Use a 3/4" drain line for backwash flow rates that exceed 7 gpm or length that exceeds 20 (6 m).
4. Both tanks must be the same height and diameter and filled with equal amounts of media.
5. The distributor tube must be flush with the top of each tank. Cut if necessary. Use only non-aerosol silicone
lubricant.
6. Lubricate the distributor o-ring seal and tank o
-ring seal. Place the main control valve on one tank and the tank
adapter on the second tank.
NOTE:
If required, solder copper tubing for tank interconnection before assembling on the main control valve
and tank adapter. Maintain a minimum of 1" distance between tanks on final assembly.
7. Solder joints near the drain must be done before connecting the Drain Line Flow Control fitting (DLFC). Leave
at least 6" (152 mm) between the DLFC and solder joints when soldering pipes that are connected on the
DLFC. Failure to do this could cause interior damage to DLFC.
8. Use only
Teflon
tape on the drain fitting.
9. Be sure the floor under the salt storage tank is clean and level.
10. Place approximately 1" (25 mm) of water above the grid plate. If a grid is not utilized, fill to the top of the air
check in the salt tank. Do not add salt to the brine tank at this time.
11. On units with a bypass, place in Bypass position.
Turn on the main water supply.
Open a cold soft water tap nearby and let water run a few minutes or until the system is free of foreign
material (usually solder) resulting from the installation. Close the water tap when water runs clean.
12. Place the bypass In Service position and let water flow into the mineral tank. When water flow stops, slowly
open a cold water tap nearby and let water run until air is purged from the unit. Then close tap.
Electrical
13. Make all electrical connections according to codes. Plug the valve into an approved power source. Do not
insert meter cable into the meter yet.
14. Tank one has control valve and tank two has adapter. See
Figure 1, page 5
or
Figure 2, page 5
.
15. Look on the right side of the control valve, it has indicators showing which position the control valve is in during
Regeneration and which tank is In Service.
Figure 3, page 7
shows the valve In Service position with tank one supplying conditioned water and tank
two on standby.
NOTE:
Make sure the meter cable is not inserted in the meter dome. Swing the timer out to expose the
program wheel (to swing timer out) grab onto the lower right corner of timer face and pull outward. See
Figure 5, page 8
.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nokia 9500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nokia 9500 in the language / languages: English as an attachment in your email.

The manual is 1,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nokia 9500

Nokia 9500 User Manual - Dutch - 119 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info