The display shows “REMOVE WATER TANK”.
Remove the water tank
The display shows “FILL WATER TANK TO 0,5l MARK” and “INSERT DESCALER TO TANK” alternat-
ingly.
Remove the lter. Fill the water tank to the 0,5 l mark with fresh water and reinsert it.
Attention: Always add the water rst to the 0,5 l mark and then the descaling agent. Never vice versa!
Please follow the manufacturer’s advice how to use the descaler.
Only now add the descaler.
The display shows “CONNECT HOSE TO SPOUT AND DRIP TRAY”.
Connect one end of the hose to the spout (g. 7).
Connect the other end to the drip tray (g. 10).
Press the rotary control.
The display shows “START DESCALING”.
Place a sufciently large bowl (minimum contents 0.5 l) under the spout (g. 1/E).
Press the rotary control.
The descaling process starts. The display shows “SYSTEM DESCALING”. The descaling process is
automatic and takes approximately 30 minutes. The descaling solution is transported through the
system in intervals.
Once the cycle is completed, the display shows “EMPTY TRAYS”.
Remove drip tray with used coffee container (g. 1/N and 1/O) and empty both.
Reinsert drip tray and used coffee container.
Remove water tank and rinse it with fresh water.
Reinsert lter in the water tank if required.
Fill the water tank with fresh water and reinsert it.
The display shows “CONNECT HOSE TO SPOUT AND DRIP TRAY”.
Connect the hose with one end to the spout (g. 7).
Connect the other end to the drip tray (g. 10).
Place a sufciently large bowl (about 0.5 l) under the spout.
Press the rotary control.
The display shows “PLEASE RINSE”.
Press the rotary control to start rinsing process.
The display shows “SYSTEM RINSING, DO NOT REMOVE HOSE”. The automatic cleaning process
is started that lasts for approximately two minutes. Once the cycle is nished, the display shows
“EMPTY TRAYS”.
Empty drip tray and used coffee container (g. 1/N and 1/O) and reinsert both.
The appliance reheats and is ready for use. The display shows the main menu.
Attention: Please remove any descaler residues on the casing immediately with a damp cloth.
5.6. Regular manual cleaning
Note: Please follow these cleaning instructions. Working with foodstuffs demands the highest degree of
cleanliness.
Attention: Never immerse the appliance in water! Do not use abrasive cleaning agents.
Use a soft, damp cloth for cleaning the casing inside and out.
Empty drip tray (g. 1/N) and used coffee container (g. 1/O) at the latest when this is indicated
on the display (only when the appliance is switched on!).
Note: Make sure when cleaning the drip tray (g. 1/N) that both metal contacts at the back are clean
and dry! Use a little detergent every now and again.
The water tank should be rinsed daily with clear water and then be re-lled daily with fresh cool
water.
Note: Dried milk residue is difcult to remove.
Therefore clean frother, hose and spout regularly.
Tip: From time to time (ideally each time the appliance will not be used for a while, at any rate in
regular intervals!) the frother needs to be completely dismantled and thoroughly cleaned under running
water.
Remove the panel from the spout (g. 1/P).
Pull the frother down and out (g. 11) and dismantle it completely (g. 1/R).
Reinsert the assembled frother into the spout (g. 11).
Replace the cover (g. 1/P).
Tip: Your appliance is equipped with back rollers (g. 1/Q), which allows you to move the appliance on
a at working top. This way, you can also clean the space underneath the appliance.
5.7. Cleaning the brew unit
Attention: Remove the brew unit only when the appliance is switched off.
When necessary the brew unit can be removed and cleaned under cold, running water. Never use
any cleaning agent, but clear, cold water only! For hygienic reasons we recommend the removal and
cleaning of the unit thoroughly after each run of the cleaning program (see 5.4.).
Open the service door on the right of the casing (g. 1/L) towards you.
Remove the brew unit by pressing the red switch and turning the handle all the way to the left
until it snaps into place (g. 12).
Carefully remove the brew unit using the handle.
Clean the brew unit under running cold water and let it dry.
Reinsert the brew unit carefully and lock by pressing down the red switch and turning the handle
all the way to the right until it snaps into place.
Close the service door and in doing so carefully place the pivots at the back of the door into the
notches. Make sure that the door (g. 1/L) completely snaps back into place.
5.8. Changing the lter
The lter will be at after about 50 l of water have been drawn. The display shows
“CHANGE FILTER”.
You can still make coffee, but we recommend changing the lter immediately.
Turn the rotary control to “SETTINGS” and press it.
Turn the rotary control to “FILTER” and press it.
Turn the rotary control to “INSERT FILTER? YES”, so the appliance recognizes the new lter:
Empty the water tank (g. 1/F and 2) and unscrew the lter, using the integrated tool at the end
of the measuring spoon (g. 4).
Discard the lter.
Press the rotary control.
The display shows “INSERT FILTER” or “FILTER INSERTED” in case the lter has already been
replaced.
Screw in the new lter into the dedicated slot in the water tank, using the integrated tool at the
end of the measuring spoon (g. 4).
Note: Do not overtighten or bend the lter.
54 55
5. Cleaning and maintenances 5. Cleaning and maintenance
