667851
8
Zoom out
Zoom in
Previous page
1/11
Next page
27
28
29
30
Channel, Group and the flash reflector zooming position are to be set on the
Remote flash.
TTL and Manual mode is available on Remote Flash, which can however only
be set by the Master flash.
Setting the Remote flash
From the 6 icons screen, select and set .
Select Remote and set . AF assist light starts
blinking every 2 seconds showing MG8000 stands by in
Remote Flash mode .
Select the line channel and set the channel. 4
channels are available from 1 to 4.
Select the line Group and set the group.
3 groups are available from A to C.
Select the line Zoom and set zooming position.
When setting MG8000 to the Remote mode, the zoom
setting system is automatically set at 24mm position. The
zooming position can be selected manually to any other
available position.
Press on/off switch to lock this condition. (Press it again to
release the lock).
Or press set , or wait about 8 seconds. The screen
shows the 6 icons screen and returns back to Remote setting page. The
function and the value remain recorded as set.
When placing more flashes, repeat the same operation procedures
instructed above.
The group can be chosen freely from A, B or C, but the channel of this
bundle of wireless flash system is to be set in one common channel.
The flash mode and the value can not be set on the Remote flash, but they
are set by the Master flash only.
Set
Set
Set
SETTING THE SLAVE FLASH
Group A
Group B
Group C
Master Flash
CREATIVE FLASH LIGHTING:
Set Master flash.
Set Slave flash/ flashes.
Make sure the channel and its group setting are correct.
Attach the Master flash to the camera and place the Slave flash/ flashes at any
desirable place within the system operation area, which is approximately 7 to
10 meters between the Master and Slave flash/ flashes depending on the
setting condition.
A variety of custom settings enable you to customize your MG8000.
TTL exposure level is accurately calibrated for standard
balance in accordance with Nissin’s standard. If any
adjustment is however required, or if you like to set your
own preferable level, it can be adjusted for about ±3 Ev. by
every 1/3 steps.
From 6 icons, select Custom setting mode and set .
Select the item to be customized and set the
value to customize.
10 custom settings are prepared.
Custom settings
Set
TTL Exposure level custom setting
A short pulse of flash light released by the test button
illuminates the subjects and monitors the lighting efficiency
on the subject.
Modeling
Illuminating the subject to find its lighting
efficiency.
Rotate
Cancel the rotating action and keep the image fixed.
The screen won’t rotate.
ft/meter
For the user who prefers distance indication by feet.
Select feet instead of meter.
To save battery energy, or simply to avoid the display illumination, the display
screen can be switched off when not in operation. Set it off, and the display
goes off in 8 seconds after the last operation. The display will not be woken
up by the camera’s shutter release. The display can only be woken up by any
operation button of MG8000.
Display
Display can be set off if it’s not necessary.
My TTL
Those customized values and conditions are effective on all modes and
memorized even when the flash unit is switched off.
To reset the customized value or conditions, select Reset, choose
“Yes” and set . All the memorized data is cancelled and MG8000 is
reset to the default value and condition.
Set
Auto Off
Reset
All those customs setting is reset to the
default value and conditions which are
provided and set at the factory.
Firmware
A firmware upgrade service is available for the
MG8000 Extreme, which provides a USB service
terminal (By local service/ local dealer) to upload
the latest software.
Buzzer
This is available for Wireless Remote mode.
When using MG8000 as a slave remote
flash, a “beep” sound indicates the master flash
triggers successfully.
Auto off timing can be selected from 10min.
15min, 30min, 45min, 60min or off (cancel).
Switch
Switch
On / Off
Key lock function is set to default for power switch.
When select “ On / Off ”, the lock function will be
replaced by “Flash off” function. An icon of flash
off will be displayed on the screen when pressing
the switch.The flash will stop function until you
press it again to release. This is available for all
modes.
Switch
Lock
Switch
Lock
Switch
Lock
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nissin MG8000 Extreme - Nikon at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nissin MG8000 Extreme - Nikon in the language / languages: English as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nissin MG8000 Extreme - Nikon

Nissin MG8000 Extreme - Nikon User Manual - German - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info