667850
8
Zoom out
Zoom in
Previous page
1/11
Next page
27
28
29
30
Single Group Slave Flash (Group A Setting)
1. Navigate the cursor to Group A
2. Navigate the cursor to Flash mode and select mode: TTL or M
Selecting TTL
1. Navigate the cursor to the Value Adjustment and set the EV
compensation level.
2. Navigate the cursor to M (Master).
3. Select TTL or --- (flash-off) in the Flash Mode
4. When TTL mode selected, move the cursor to the Value Adjustment and
set the EV compensation level.
5. Navigate the cursor to M (Master).
6. Select TTL or --- (FLASH OFF) in the Flash Mode.
7. When TTL mode selected, Navigate the cursor to the Flash Adjustment
and set the power ratio.
Selecting M
1. Navigate the cursor to the Flash Adjustment and set the power ratio
2. Navigate the cursor to M (Master).
3. Select M or --- (FLASH OFF) in the Flash Mode.
4. When M mode selected, navigate the cursor to the Flash Adjustment
and set the power ratio.
Note: When setting --- (FLASH OFF) mode, the master flash may flash when
shutter released. This flash is however the monitoring flash (pre-flash) before the
camera’s shutter opens and is not be exposed in the actual picture.
Multiple Group Slave Flash (Group B & C Setting)
Group A MUST be set, in order to add Group B
Adding Group B
When TTL mode selected in Group A 
1. Navigate the cursor to GROUP B, and select TTL in the operation mode
box.
2. Navigate the cursor to Flash Adjustment and select the power level ratio
between Group A and Group B.
^The power level ratio can be selected from 13 different combinations, such
as A:B = 8:1 – 5.6:1 – 4:1 – 2.8:1 – 2:1 – 1.4:1 – 1:1 – 1:1.4 – 1:2 – 1:2.8 –
1:4 – 1:5.6 and 1:8
3. Navigate the cursor to M (Master).
4. Select TTL or --- (flash-off) in the Flash Mode.
5. When TTL mode selected, navigate the cursor to the Flash Adjustment and
set the EV Compensation.
When M mode selected in Group A
1. Navigate the cursor to GROUP B, and select M in the operation mode box.
2. Navigate the cursor to Flash Adjustment and select the power ratio
3. Navigate the cursor to M (Master).
4. Select M or --- (flash-off) in the Flash Mode.
5. When M mode selected, navigate the cursor to the Flash Adjustment
and set the power ratio..
Adding Group C
Group A & B (A:B) MUST be set, in order to add Group C.
^The group C is independently set out from the power ratio combination.
When TTL Mode selected in Group A & B:
1. Navigate the cursor to GROUP C, and select TTL in the Flash Mode.
2. Navigate the cursor to Flash Adjustment and select the EV compensation.
3. Navigate the cursor to M (Master).
4. Select TTL or --- (flash-off) in the Flash Mode.
5. When TTL mode selected, navigate the cursor to the Flash Adjustment and
set the EV Compensation.
When M Mode selected in Group A & B:
1. Navigate the cursor to GROUP C, and select M in the Flash Adjustment.
2. Navigate the cursor to Flash Adjustment and select the power ratio.
3. Navigate the cursor to M (Master).
4. Select M or --- (flash-off) in the Flash Mode.
5. When M mode selected, navigate the cursor to the Flash Adjustment
and set the power ratio.
^This 3 group slave flash technology is recommended to shade off or remove the
shadow behind subject which may be caused by the lighting produced by Group
A and/or B.
The modes available on the Master flash are TTL and M mode.
The master flash sets the signal transmission channel, flash reflector zooming
position, flash mode of the master flash itself and flash mode and value
adjustment of the slave flash at A, B and C respectively.
Setting the Master flash
In the main page
Select Wireless mode.
In the Wireless page
Select Master mode.
In the Master page
Navigate the cursor and adjust the value according to the
instruction at the bottom bar.
Cursor Navigation
Value Adjust
Channel Select
Select Channel: Ch1, Ch2, Ch3 & Ch4
Zoom Select
Select Zoom Mode: Auto, 24mm, 28mm, 35mm, 50mm,
70mm, 85mm, 105mm
Group Setting
Group
M = Master Flash
A = Group A
B = Group B
C = Group C
Flash Mode
TTL = TTL Mode
M = Manual Mode
--- = Flash off
Value Adjustment
Ev compensation at TTL mode
(-3.0Ev to +3.0Ev)
Power Ratio at M mode
(1/1, 1/2, 1/4, 1/8, 1/16,
1/32, 1/64, 1/128)
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nissin MG8000 Extreme - Canon at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nissin MG8000 Extreme - Canon in the language / languages: English as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nissin MG8000 Extreme - Canon

Nissin MG8000 Extreme - Canon User Manual - German - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info