Manual Nilfisk Supreme LCD (page 6 of 26) (English)

586824

Zoom out

Zoom in

1/26

2.1 Fitting the wall bracket

Position the holder so that there is plenty of space above and

below the place where the vacuum unit is to be located. Make

sure there is a minimum of 500 mm free space above the

container. Mark the positions for the four screw holes with a

pen or similar. Then select appropriate screws and, if neces-

sary, wall plugs for the type of wall surface to which the brack-

et is to be attached. Drill the four holes for the wall bracket.

The diameter of the screw holes in the holder is 5 mm. Fit the

wall bracket with the large opening pointing upwards, see Fig.

1. Tighten the screws so that the holder is held ﬁ rmly in place

(screws provided).

2.3 Connecting the machine

The machine is connected with the suction pipe in the uppermost position and the exhaust

pipe in the lower position.

This connection should not be glued but can be taped when the unit is serviced at a later

date. The suction pipe socket can be ﬁ tted to two different points depending on the direc-

tion in which you would like to install the pipe system.

To relocate the suction pipe socket, you need to do the following:

1. Release the suction pipe socket by unscrewing the four combination Torx screws with a

Torx T20 or an ordinary screwdriver, Fig. 3.

2. Pull the socket out of the machine, see Fig. 4.

3. Loosen the plug blanking off the outlet to which you intend moving the suction pipe

socket. Unscrew the four combination Torx screws. Remove the blanking plug from the

machine.

4. Adapt (move) the suction pipe socket to the new outlet. NB! The socket is marked ”Up”.

Make sure the socket is ﬁ tted with ”Up” uppermost. Fasten the socket by ﬁ tting and

tightening the four screws, Fig. 5.

5. Fit the blanking plug to the outlet previously occupied by the suction pipe socket. Use the four screws to hold it in place.

The exhaust pipe must be ﬁ rmly attached to the wall to ensure its connection with the socket does not loosen. Remember

that you will need to be able to turn the bent pipe in different directions to ensure a suitable pipe layout. Then connect up

the exhaust pipe and mufﬂ er, Fig 6. Fit the central vacuum cleaner so that the exhaust pipe is as short as possible, max.

5 metres. Take the surroundings into consideration when positioning the exhaust. For this reason, you should always ﬁ t a

mufﬂ er.

For additional information concerning the assembly and installation of the pipe system and low-current lead, please refer to

the separate assembly instructions supplied with the pipe package.

2 Vacuum unit Supreme 100 assembly instructions

2.2 Locating the vacuum cleaner on the

wall bracket

Position the vacuum unit so that the wall bracket is directly

above the wall bracket, see Fig. 2. Lower the machine down

on to the wall bracket. Make sure the corresponding bracket

on the machine is held ﬁ rmly in place by the wall bracket.

Fig. 1 Fig. 2

Fig. 3 Fig. 4 Fig. 5

Exhaust

Inlet

Fig. 6

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Nilfisk Supreme LCD in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nilfisk Supreme LCD

Nilfisk Supreme LCD User Manual - German - 27 pages

Nilfisk Supreme LCD User Manual - Danish - 89 pages

Nilfisk Supreme LCD User Manual - French - 25 pages

Nilfisk Supreme LCD User Manual - Swedish, Finnish - 89 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Nilfisk Supreme LCD Manual

Product: