787649

Nilfisk SC2000 Manual

72
Zoom out
Zoom in
Previous page
1/116
Next page
ENGLISH INSTRUCTIONS FOR USE
14 SC2000 - 9100000383 01/2015
revised 07/2017
MACHINE START AND STOP
Starting the machine
1. Prepare the machine as shown in the previous paragraph.
2. Place the user key (52) in the key reader (41), then press the push-button (42) to start the machine.
3. In the fi rst 2 seconds after machine start-up, the display (51) indicates the machine working hours (51-A) and the type of
batteries installed (51-B).
NOTE
Check the battery charge level.
When the display shows at least one segment of the battery symbol (51-C) which is on but not fl ashing, the machine is
ready for use.
When the battery symbol (51-C) shows just one segment fl ashing, the batteries have to be charged (see the procedure in
Maintenance chapter).
4. Drive the machine to the working place, by starting it with both hands on the steering wheel (1) and by pressing the drive pedal
(2).
The drive speed can be adjusted from zero to maximum speed according to the pressure on the drive pedal (2).
5. The forward/reverse gear is selected with the relevant lever (49) which is at the right of the steering wheel.
NOTE
The driver’s seat (12) is equipped with a safety sensor, which allows the machine to be driven by pressing the pedal (2)
only when the operator is on the driver’s seat.
NOTE
The machine is equipped with an anti-skid safety system (display icon (51-J)) that reduces the speed when turning and
when the machine tilts laterally, irrespectively of the pressure on the pedal.
In this case, the reduction of speed is not a malfunction but a characteristic that improves the machine stability and
safety in every condition.
CAUTION!
In case of use of the machine on slopes, drive very carefull and reduce the speed mostly when the fl oor is wet or
slippery.
Always take the ramp perpendicularly to the slope.
To park the machine on slope, reach the parking position and turn off the machine.
Never exceed the gradients indicated on the “Technical Data” paragraph.
Stopping the machine
6. Stop the machine by releasing the drive paddle (2). It is not necessary to lock the machine during stopping or parking, because
the electromagnetic brake on the wheels turn on automatically when the drive pedal is not pressed.
7. Turn off the machine by pressing the push-button (42) and remove the user key (52).
NOTE
The machine is running without the user key (52) in the key reader (41), it automatically switches off after 10 seconds of
complete idle.
NOTE
If the machine is on but not working, it automatically turns off after 5 minutes.
CAUTION!
In the event of an emergency, to stop all machine functions immediately, fi rmly press the push-button (5).
To reset the machine operation, lift the recovery tank assembly (17) and reconnect the battery connector (6).
revised 01/2018
… 72 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nilfisk SC2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nilfisk SC2000 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 15.15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info