If your machine shipped with batteries installed do the following:
Check that the batteries are connected to the machine.
Turn ON the Key Switch (A) and check the Battery Indicator (F8). If the gauge is completely fi lled the batteries are ready for use. If the gauge is less than
full the batteries should be charged before use. See the “Charging The Batteries” section.
IMPORTANT!: IF YOUR MACHINE HAS AN ONBOARD BATTERY CHARGER REFER TO THE OEM PRODUCT MANUAL FOR INSTRUCTIONS
REGARDING SETTING THE CHARGER FOR BATTERY TYPE.
If your machine shipped without batteries installed do the following:
Consult your Authorized Nilfi sk dealer for recommended batteries.
Install the batteries by following the instructions below.
IMPORTANT!: IF YOUR MACHINE HAS AN ONBOARD BATTERY CHARGER REFER TO THE OEM PRODUCT MANUAL FOR INSTRUCTIONS
REGARDING SETTING THE CHARGER FOR BATTERY TYPE.
INSTALL THE BATTERIES
WARNING !
Use extreme caution when working with batteries. Sulfuric acid in batteries can cause severe injury if allowed to contact the skin or
eyes. Explosive hydrogen gas is vented from inside the batteries through openings in the battery caps. This gas can be ignited by
any electrical arc, spark or fl ame. If battery acid makes contact with your skin, fl ush the affected area with water for 5 minutes and
seek medical attention.
When Servicing Batteries...
• Remove all jewelry.
• Do not smoke.
• Wear safety glasses, a rubber apron and rubber gloves.
• Work in a well-ventilated area.
• Do not allow tools to touch more than one battery terminal at a time.
•ALWAYS disconnect the negative (ground) cable fi rst when replacing
batteries to prevent sparks.
•ALWAYS connect the negative cable last when installing batteries.
CAUTION !
Electrical components in this machine can be severely damaged
if the batteries are not installed and connected properly. Batteries
should be installed by Nilfi sk or by a qualifi ed electrician.
1 Empty the Recovery Tank (15) using the Recovery Tank Drain Hose (30).
2 Turn the Key Switch (A) off (O) and remove the key. Unlatch (29) then swing
open the Recovery Tank Cover (13) and set the Prop Rod (32).
3 Tip the Recovery Tank (15) back towards the operator’s platform to expose
the battery compartment.
4 Using (2) people and an appropriate lifting strap, carefully lift the batteries
into the compartment tray exactly as shown. Refer to the molded diagram
on the underside of the Recovery Tank Cover.
5 See Figure 1. Install battery cables as shown and tighten the nuts on the
battery terminals.
6 Install the battery boots and secure tightly to the battery cables with the
supplied tie straps.
7 Connect the machine’s main power cables to the batteries or if so equipped
plug together the battery connector (33). Close the recovery tank cover.
When changing batteries or the charger, please contact your local
authorized service center for correct battery, charger and machine
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Nilfisk SC1500 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Nilfisk SC1500 in the language / languages: English as an attachment in your email.
The manual is 16.82 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
