586823

Nilfisk Performer 250 Manual

15
Zoom out
Zoom in
Previous page
1/26
Next page
47
All work involving the 240 volt mains electricity
supply must be carried out by a qualifi ed electrical
contractor with full knowledge of the relevant safety
regulations.
The vacuum cleaner will not start
Thermal protector
The vacuum cleaner has a thermal cut-out that trips if the
vacuum cleaner becomes overheated.
Supreme 100 / Supreme 150 / Performer 150 /
Supreme 250 / Performer 250
If this happens - unplug the main power cord to reset the
vacuum cleaner. Wait 5-10 minutes to allow the machine to
cool down. While you are waiting, check the hose, dust bag
and fi lter to be sure that nothing is blocking the fl ow of air
through the machine. The vacuum cleaner should now start
again. If the cut-out trips again, you need to get a service
fi rm to remedy the fault.
Supreme LCD
When the overheat symbol in the display on the cleaner is
activated (models with display) the cleaners’ thermal cut-out
has tripped. For more information regarding thermal cut out,
see Overheat indicator.
Other troubleshootings
• Are you using the correct hose?
Only the original hoses fi t correctly.
• Does the vacuum cleaner start when you try a different
vacuum socket? If so, there is a fault in the electrical con-
nection to the fi rst socket. Unscrew the socket and check
the connection at the back.
• Is the power supply connected to the vacuum unit?
• Is there power at the socket?
• Is the low-voltage lead connected to the vacuum unit?
• The batteries to the radio remote control (wireless version
of vacuum cleaner) may have been discharged. Replace
the batteries with new ones, type 1.5V AAA.
The vacuum cleaner will not stop
• Has a metal object become lodged in one of the vacuum
sockets causing the pins to become fused?
Poor suction power
• Are all the vacuum sockets closed properly?
• Has something become jammed in one of the vacuum
sockets?
• Is the container lid closed properly?
• Is the gasket between the container and the lid in place?
• Is it damaged?
• Is the pipe system blocked?
• Is the dust bag full or clogged?
• Is fi lter clogged?
Supreme LCD Display
The Supreme LCD model has a display giving information
about the machine, Fig. 21.
Speed level
When the start button is pushed or the hose is connected to
the wall socket, the display will turn on and show the speed
level.
10 Troubleshooting
Dust bag/bag fi lter indicator
When the dust bag/fi lter symbol starts to fl ash during opera-
tion, the cleaner tells you that it is almost time to clean the
bag fi lter and replace the dustbag. When it is time to do so,
symbol will be lit continuously. The dust bag/fi ler symbol will
be lightened after every 20 operation hours of the cleaner. If
the symbol is lit, do like this: Turn off the cleaner by the hose
handle (remote versions) or remove the suction hose from
the wall inlet or by pushing the on/off switch on the display.
Then check if the bag fi lter/dustbag is clogged. Replacement
is described in chapters 7.1, 7.2, 7.3 and 7.4.
Reduced airfl ow indicator - lit
The reduced airfl ow symbol on the display indicates that
the airfl ow through the vacuum cleaner is reduced. After 30
seconds of operation with reduced airfl ow, the vacuum motor
will be shot down in order to prevent damage to the motor. If
the reduced airfl ow symbol is lit and the motor has been shut
down, do like this: Check the bag fi lter and dust bag (see
chapters 7.1, 7.2, 7.3 and 7.4) to see if anything is blocking
the airfl ow. Remove the material causing the reduced air fl ow
symbol to indicate.
Service indicator
When the service symbol starts fl ashing, the motor will run
for one more hour before it stops/will not start. The purpose
of the service symbol is to inform you that it is time to order
service of the cleaner. When the symbol is continuously lit,
the run time counter in the cleaner has counted that the al-
lowed amount of run time has passed. You must now contact
an authorised service workshop and let them perform a ser-
vice of the cleaner and to reset the run time counter.
Overheat indicator - fl ashing
The overheat symbol indicates that the cleaner has become
overheated. The cleaner stops automatically. Unplug the
main power cored to reset the vacuum cleaner and wait 5-10
minutes to allow the machine to cool down. While you are
waiting, check the hose, dust bag and fi lter to be sure that
nothing is blocking the fl ow of air through the machine.
Signal indicator - fl ashing
When the symbol is fl ashing, the hose handle is out of range
and there is no connection to the cleaner. The cleaner will
automatically stop after 30 min. if the hose handle or the
cleaner has not been activated.
WARNING!
Blockages can occur if:
a) the tools and accessories are not used as di rect ed
at all times.
b) wet or damp carpets are vacuumed.
c) foreign objects are vacuumed up when the tools
are not affi xed to the hose.
d) the wall sockets are not kept open until the system
motor stops completly
e) the fi lter and bags are not regularly cleaned and
replaced as per manufacturers in struc tions.
NB! Blockages are caused by misuse and are not cov-
ered by the guarantee or warranty.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nilfisk Performer 250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nilfisk Performer 250 in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nilfisk Performer 250

Nilfisk Performer 250 User Manual - German - 27 pages

Nilfisk Performer 250 User Manual - French - 25 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info