529023
4
Zoom out
Zoom in
Previous page
1/12
Next page
4
1.0 Preparation EN
Extension cable
Extension cables should be of a watertight con-
struc tion and comply with the below-men tioned
requirements for length and cable dimensions.
1,5 mm² max 20 m
2,5 mm² max 30 m
Cable connections should be kept dry and off the
ground.
Always uncoil the extension cable com plete ly to
avoid heat dam age to the cable.
Water connection
Connect the high pressure washer by means of a
water hose to the water tap (pressure of inlet wa -
ter, max. 10 bar - temperature of inlet water, max.
60°C). You may use an or di nary ½" gar den hose of
min. 10 m and max. 25 m. At tach the hose using
a quick connector. NOTE: Connection to the public
mains according to regulations.
This high pressure washer is only allowed
to be connected with the drinking water
mains, when an appropriate backfl ow
preventer has been installed, Type BA according to
EN 1717. The backfl ow preventer can be ordered
under number 106411177. The length of the hose
between the backfl ow preventer and the high pres-
sure washer must be at least 10 metres to absorb
possible pressure peaks (min diameter ½ inch).
Operation by suction (for example from a rainwater
vessel) is carried out without backfl ow preventer.
Recommended suction set: 126411387.
As soon as water has fl own through the BA valve,
this water is not considered to be drinking water any
more.
IMPORTANT! Only use water without any im pu-
ri ties. If there is a risk of running sand in the inlet
water (i.e. from your own well), a fi lter should be
mounted.
Safety precautions
WARNING! High pressure jets can
be dan ger ous. Nev er direct the wa-
ter jet at per sons, pets, live elec tri-
cal equip ment or the ma chine itself.
The operator and anyone in the im-
me di ate vi cin i ty of the site of clean-
ing should take action to pro tect
them selves from being struck by
debris dis lodged dur ing op er a tion.
Wear goggles during op er a tion.
Before starting up your high pressure wash er, we
advise you to carefully read through this instruction
manual. Fol low all instructions to min i mize the risk
of injuries when using the ma chine.
Prior to operation
Before you start up your new machine for the fi rst
time, you must mount the holder for the spray lance.
It is fi xed at the top of the transport handle.
1. Insert the holder in the recess of the handle (see
illu.).
2. Fix the holder with the screw.
Mount water fi lter and water inlet connection (4).
PRO 130/150/160 X-TRA: Mount the handle for the
hose reel.
Before starting up your machine please check it
care ful ly for any de fects. If you fi nd any, do not start
up your ma chine and con tact your Nilfi sk distributor.
Especially check:
The insulation of the electric cable should be
fault less and without any cracks. If the elec tric
cable is damaged, it should be replaced by an
authorized Nilfi sk distributor.
Mains power connection
The following should be observed when connecting
the high pressure washer to the elec tric in stal la tion:
Only connect the machine to an in stal la tion with
earth connection.
The electric installation shall be made by a cer ti -
ed electrician.
It is strong ly rec om mend ed that the elec tric sup -
ply to this ma chine should in clude a re sid u al
cur rent device (GFCI).
1
2
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nilfisk P 160.1 X-TRA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nilfisk P 160.1 X-TRA in the language / languages: English as an attachment in your email.

The manual is 2,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nilfisk P 160.1 X-TRA

Nilfisk P 160.1 X-TRA User Manual - German - 13 pages

Nilfisk P 160.1 X-TRA User Manual - Dutch - 13 pages

Nilfisk P 160.1 X-TRA User Manual - French - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info