Manual Nilfisk-ALTO SCRUBTEC 545B (page 70 of 100) (English, German, Dutch, French)

609446

Zoom out

Zoom in

1/100

ENGLISH INSTRUCTIONS FOR USE

SCRUBTEC 545B / 545BL / 553B / 553BL / BOOST 5 - 9097054000

02/2007

05/2015

SQUEEGEE CLEANING

NOTE

The squeegee must be clean and its blades must be in good conditions in order to get a good drying.

CAUTION!

It is advisable to wear protective gloves when cleaning the squeegee because there may be sharp debris.

1. Drive the machine on a level oor.

2. Turn the ignition key (80) to “0”.

3. Lower the squeegee (25) with the lever (10).

4. Loosen the handwheels (26) and remove the squeegee (25).

5. Disconnect the vacuum hose (15) from the squeegee.

6. Wash and clean the squeegee (Fig. 4). In particular, clean the compartments (A, Fig. 4) and the vacuum hole (B) from dirt

and debris. Check the front blade (C) and the rear blade (D) for integrity, cuts and tears; if necessary replace them (see the

procedure in the following paragraph).

7. Install the squeegee in the reverse order of removal.

SQUEEGEE BLADE CHECK AND REPLACEMENT

1. Clean the squeegee (Fig. 5) as shown in the previous paragraph.

2. Check that the edge (E, Fig. 5) of the front blade (C) and the edge (F) of the rear blade (D) lay down on the same level, along

their length; otherwise adjust their height according to the following procedure:

• Remove the tie rod (G), disengage the retainers (M) and adjust the rear blade (D); then engage the retainers and install the

tie rod.

• Loosen the handwheels (I) and adjust the front blade (C); then tighten the handwheels.

3. Check the front blade (C) and rear blade (D) for integrity, cuts and tears; if necessary replace them as shown below. Check

that the front corner (J) of the rear blade is not worn; otherwise, overturn the blade to replace the worn corner with an integral

one. If the other corners are worn too, replace the blade according to the following procedure:

• Remove the tie rod (G), disengage the fasteners (M) and remove the retaining strip (K), then replace/overturn the rear

blade (D). Install the blade in the reverse order of removal.

• Unscrew the handwheels (I) and remove the retaining strip (L), then replace the front blade (C). Install the blade in the

reverse order of removal.

After the blade replacement (or overturning), adjust the height as shown in the previous step.

4. Connect the vacuum hose (15) to the squeegee.

5. Install the squeegee (25) and screw down the handwheels (26).

6. If necessary, adjust the squeegee adjusting handwheel (27).

S311336

Figure 5

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Nilfisk-ALTO SCRUBTEC 545B in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 7,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Nilfisk-ALTO SCRUBTEC 545B Manual

Product: