3274
27
Zoom out
Zoom in
Previous page
1/39
Next page
52 53
Technical Operation
Multiple Flash Operation Using the Infrared Remote Commander
With the Infrared Filter SW-9IR, you can use the master SB-50DX unit as
an infrared remote commander to perform wireless multiple flash
operation. With the SW-9IR attached, the master SB-50DX unit fires
infrared rays that do not expose normal film to trigger the slave SB-80DX,
50DX, 30 unit or other slave flash unit (with the SU-4) to illuminate the
subject without master flash unit lighting.
Multiple flash operation using the infrared remote commander
1. Attach the Infrared Filter SW-9IR to the
SB-50DX flash head.
Attach the SW-9IR so that it fits into the
grooves on the flash head.
To remove the SW-9IR, pull it out from the
groove on one side.
2. Attach the SB-50DX to the camera body for use as a master flash unit.
Before attaching the SB-50DX, turn off the SB-50DX and camera.
Do not use the camera’s built-in Speedlight.
3. Shoot following the same procedure as in wireless multiple flash operation
without infrared remote commander (p. 48).
Press the SLAVE button on the SB-50DX (master flash unit) for approx. 1 sec. to
set the Speedlight to Wireless Flash mode (p. 48)
Use another SB-80DX, 50DX, 30 and/or other Speedlight with the SU-4 (p. 56)
as slave flash unit(s).
With the SW-9IR attached to the master SB-50DX, the effective range of the light
sensor on the slave flash unit is approx. 7m (23 ft.) in the Auto Slave Flash mode
(p. 49) or approx. 40m (131 ft.) in the Manual Slave Flash mode (p. 52).
Carrying the Infrared Filter SW-9IR
When not used, the SW-9IR can be placed on
top of the flash head. Fit the SW-9IR into the
grooves on the flash head.
Wireless Multiple Flash Operation—continued
Manual wireless multiple flash operation with the SB-50DX set at
Manual Slave Flash mode
To fire the slave SB-50DX unit placed distant from the master flash unit (or
where the light of the master flash does not reach) without cords, set the
slave SB-50DX unit to Manual Slave Flash mode. Slave SB-50DX unit detects
the light from other flash unit(s) such as a master flash unit and fires at full
output.
Press the SLAVE button for approx. one second to
activate for Auto Slave Flash mode or for
Manual Slave Flash mode indicated in the LCD
panel. If the is shown, press the MODE to set
the Manual Slave Flash mode with indication.
Aperture is determined by the guide number (p. 33)
and flash shooting distance. You can control
exposure by varying flash-to-subject distance. (Test
shooting is recommended.)
Effective range of the SB-50DX’s light sensor in the
Manual Slave Flash mode is approx. 40m (131 ft.).
In the Manual Slave Flash mode, the light sensor on
the slave SB-50DX becomes very sensitive; manual
wireless multiple flash shooting may be performed
even if the light sensor is not facing the master
flash unit.
Set flash mode on the master flash unit to TTL auto
flash mode without Monitor pre-flash (p. 27) (See
“Canceling Monitor pre-flashes”, p. 47), non-TTL
auto or Manual (p. 31). (Usable flash mode depends
on camera/Speedlight combination. See instruction
manual of your camera and Speedlight).
SB-50DX (E) 02.12.9 2:33 PM Page 52
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nikon SB 50DX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nikon SB 50DX in the language / languages: English as an attachment in your email.

The manual is 1,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nikon SB 50DX

Nikon SB 50DX User Manual - German - 39 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info