733845

Nikon Nikon Laser Rangefinder Callaway RAZR Manual

23
Zoom out
Zoom in
Previous page
1/35
Next page
44 45
44 45
En
Fr
Es
Pt
En
Fr
Es
Pt
1. 『 』- Repère de cible/Irradiation laser
『』- Visez la cible. Positionnez la cible au centre du réticule.
『 』- S'affiche lorsque le laser est utilisé pour une mesure.
(Ce télémètre laser ne comporte pas de fonction de mesure unique.)
Attention: ne regardez pas dans l'objectif lorsque ce symbole est affiché.
2．『 』: Affichage de l'état distance / mesure
Indique sous forme numérique la distance mesurée en mètres / yards. Indique
aussi l'état de la mesure tel que « Measurement in progress » (mesure en cours),
« Measurement unsuccessful » (échec de la mesure) ou « Unable to measure »
(mesure impossible).
<Exemples de résultats de mesure>
(Distance)
Affichage des résultats: ( ≧100m / yards) par ex. 234 mètres = 『』
Affichage des résultats: ( ＜100m / yards) par ex. 76,5 yards = 『』
『』 -Mesure en cours
『』 - Échec de la mesure ou mesure de distance impossible
3. 『』Unités d'affichage
『』Indique, en mètres, la distance en cours de mesure.
『』Indique, en yards, la distance en cours de mesure.
4. 『』 Indique l'état de la pile. (Reportez-vous à la section «Remplacement de la pile »)
* Bien que l'écran ACL ait été fabriqué grâce à la technologie la plus avancée, il est impossible d'éliminer toutes
les poussières. Un écran ACL affiche généralement le même grossissement ou un grossissement plus faible,
mais l'ACL de cet appareil est très agrandi grâce à la lentille de l'oculaire. Pour cette raison, de la poussière
peut apparaître comme un défaut lors d'une mesure. Cependant, la précision de la mesure n'en est pas
diminuée pour autant.
Écran interne Mode d'emploi
Attention — L'emploi de commandes, réglages ou
performances de procédure autres que ceux
spécifiés dans ce manuel peut entraîner une
exposition à des rayonnements dangereux.
1. Installez une pile dans le logement prévu
à cet effet. (Reportez-vous à la section
« Remplacement de la pile »).
2. Correction dioptrique
Réglez la correction dioptrique pour obtenir une
image nette sur l'écran ACL.
Tournez d'abord la bague de réglage dioptrique
dans le sens antihoraire jusqu'à ce qu'elle soit
totalement en butée. Ensuite, mettez l'appareil
sous tension pour activer l'écran ACL quand vous
regardez dans le Télémètre Laser Nikon. Tournez la
bague de réglage dioptrique dans le sens horaire
jusqu'à ce que l'affichage soit net.
Si la correction dioptrique ne correspond pas à
votre vue, vous aurez des difficultés à effectuer la
mise au point sur le sujet.
3. Mesure
Avant de prendre les mesures, veillez à confirmer les
paramètres du dispositif.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
1. Appuyez sur le bouton
POWER pour mettre l'appareil
sous tension.
2. Visez la cible.
Immédiatement après
la mise sous tension
(initialisation).
En veille. Cible visée.
3. Appuyez une fois sur le bouton POWER pour prendre une mesure
continue pendant 8 secondes. (Le mode mesure unique n'est pas
disponible sur ce télémètre laser).
Mesure en cours.
4. L'affichage interne affiche les témoins clignotants « distance » ou «
échec de la mesure » pendant 8 secondes. (Le signe de rayonnement
laser clignote lors de la prise de mesure).
Échec de la mesure ou
mesure de distance
impossible.
Affiche les
résultats mesurés.
(Cible 1)
Affiche les résultats
mesurés. (Cible 2)
5. Une fois la mesure continue effectuée, les résultats mesurés
s'affichent pendant 8 secondes, puis l'appareil se met hors tension.
Si vous appuyez sur le bouton POWER lorsque l'appareil est sous
tension (pendant que l'affichage interne est éclairé), une autre
mesure de 8 secondes s'initie.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nikon Nikon Laser Rangefinder Callaway RAZR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nikon Nikon Laser Rangefinder Callaway RAZR in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 9,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info