604470

Nikon Laser 550A S Manual

22
Zoom out
Zoom in
Previous page
1/73
Next page
42
Jp
En
Fr
Es
Pt
43
Jp
En
Fr
Es
Pt
Operational Summary
Caution—use of controls or adjustments or
performance of procedures other than those
specified herein may result in hazardous radiation
exposure
1. Install a battery in the battery chamber. (See "Changing
Batteries")
2. Rubber eyepiece cup
Both eyeglass wearers and non-wearers can use this
rangefinder without attaching the rubber eyepiece cup.
3. Diopter adjustment
Adjust diopter to obtain a clear image in the LCD.
First, rotate the diopter adjustment ring counterclockwise
until it comes to a complete stop. Next, turn on the power
to activate the LCD when you look through the Nikon Laser
550A S. Rotate the diopter adjustment ring clockwise until
the display comes into focus.
If the diopter is not adjusted to correspond to your
eyesight, you may not be able to clearly focus your subject.
4. Measuring
Note: See the chapter "External and Internal display" for external
LCD panel.
Note: Depressing and holding down the POWER button causes
all symbols to be displayed in the internal LCD panel. After
you remove your finger from the POWER button, the last-
used setting is displayed. (If you briefly press the POWER
button then remove your finger, the LCD panel may
display the last-used setting without displaying all of the
symbols. This is not a malfunction or other problem.)
Before measuring, be sure to confirm settings, such as unit,
measurement/display mode and priority mode.
◎: See the relevant mode section in this manual for setting.
POWER
Set FULL/Limited
measurement mode
LCD is illuminated
Set your desired modes
◎
Align the reticle
with the target
POWER
appears
Results are converted
to the mode set and
displayed.
MODE
Indication
remains
illuminated for
30 sec.
30 seconds pass without operation ＊
Power off: LCD indications disappear
Measure again
Fail to measure
Cannot measure
Successfully
measured
For continuous distance
and angle measurement
(up to 20 seconds), keep
button depressed.
※
or
☆
☆【Continuous measurement mode】
Keeping the POWER button depressed allows you to
perform continuous measurement for 20 seconds.
Blinks while performing measurements.
When measuring a pin at a golf course, for example, use First
Target Priority and Continuous measurement mode for easy
measurement. With no objects between you and the pin, the
smallest number is the distance to your targeted pin.
※ See the the chapter "External and Internal display" for details
regarding the operations and results display of the various
modes.“
＊ Power turns off 30 seconds after the last operation.
5. Selecting display unit (Factory default setting is yard.)
1. Confirm the LCD panel is on.
2. Press and hold the
button for approx. two seconds.
3. When display unit has switched, release the
button.
4. After the unit is set, results will be converted and displayed in
the your selected measurement unit.
Meter
[ ]
Yard
[ ]
By pressing the MODE button, modes will change in the order
indicated above.
The angles and heights of two points are displayed only at the
full-mode setting.
Linear Distance [ ]
Horizontal Distance [ ]
Angle [ ]
Height [ ]
Vertical Separation
between 2 points
point
[ ]
1. Confirm the LCD panel is on.
2. Press
button within 0.5 seconds.
3. Release
button to switch the mode.
4. Repeat steps 2 and 3 until your desire mode is displayed.
5. Switching the mode after measurement converts the
results to the new mode.
6. After the mode is set, measurements are performed in the
new mode.
7. Switching Full/Limited modes (default setting is limited
mode)
1. Confirm the power is off (LCD is off).
2. Press and hold
button, then depress and hold
button within 0.5 second.
3. Continue to press and hold both buttons, (more than 2
seconds),to confirm the internal display is on.
When these buttons are pressed, all symbols are displayed .
6. Switching measurement/display modes (Factory default
setting is linear distance measurement mode)
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nikon Laser 550A S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nikon Laser 550A S in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 48,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info