Manual Nikon Coolshot (page 87 of 139) (All languages)

570991

Zoom out

Zoom in

1/139

172 173

Podsumowanie dotyczące obsługi

Uwaga — korzystanie z elementów sterowania

lub regulacji, czy też wykonywanie procedur w

sposób inny, niż określony w niniejszym

podręczniku, może spowodować narażenie na

niebezpieczne promieniowanie.

1. Włóż baterię do komory baterii. (Patrz „Wymiana

baterii”)

2. Regulacja dioptrii

Przeprowadź regulację dioptrii, aby uzyskać

wyraźny obraz na ekranie LCD.

Najpierw obróć do końca pierścień regulacji dioptrii

w kierunku przeciwnym do ruchu wskazówek

zegara. Następnie włącz zasilanie, aby aktywować

ekran LCD podczas spoglądania przez dalmierz

laserowy Nikon. Obróć pierścień regulacji dioptrii w

prawo, do momentu gdy obraz będzie ostry.

Jeśli regulacja dioptrii nie zostanie

przeprowadzona, właściwe ustawienie celu na

obiekcie może nie być możliwe.

3. Pomiar

Przed rozpoczęciem pomiaru sprawdź ustawienia

urządzenia.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

1. Naciśnij przycisk

POWER (Zasilanie) w celu

włączenia urządzenia.

2. Skieruj na cel.

Natychmiast po

włączeniu.(Inicjalizacja)

Tryb czuwania. Ustawianie na celu.

3. Naciśnij przycisk POWER (Zasilanie) jeden raz, aby rozpocząć

ciągły pomiar przez 8 sekund. (Tryb pojedynczego pomiaru jest

niedostępny w tym modelu dalmierza laserowego.)

Pomiar.

4. Przez 8 sekund wewnętrzny ekran wyświetla na przemian wskazanie

„odległość” i „błąd pomiaru”. (Oznaczenie promienia lasera miga.)

Pomiar zakończony

niepowodzeniem

lub brak możliwości

dokonania pomiaru.

Wyświetlanie

pomierzonej

wartości. (Cel 1)

Wyświetlanie

pomierzonej

wartości. (Cel 2)

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

5. Po wykonaniu ciągłego pomiaru przez 8 sekund wyświetlane

są wyniki, a następnie zasilanie jest wyłączane. Po naciśnięciu

przycisku POWER (Zasilanie) podczas włączonego zasilania (gdy

wewnętrzny wyświetlacz jest aktywny) rozpoczyna się kolejny

pomiar 8-sekundowy.

Przykładowo, podczas mierzenia odległości do flagi na polu

golfowym skanowanie flagi podczas pomiaru pozwala łatwiej

uzyskać odczyt. Jeśli pomiędzy użytkownikiem a flagą nie znajdują

się żadne obiekty, najkrótszy wynik to odległość do flagi.

4. Wybór wyświetlanej jednostki miary

(domyślne ustawienie to jardy)

1. Upewnij się, że wewnętrzny ekran LCD jest włączony.

2. Naciśnij i przytrzymaj przycisk MODE przez 2 sekundy

lub dłużej.

3. Gdy wyświetlana jednostka miary zostanie

zmieniona, puść przycisk MODE.

4. Po ustawieniu jednostki wyniki zostaną przeliczone i

wyświetlone w wybranej jednostce miary.

Metry [ ]Jardy [ ]

6. Informacja o niskim stanie baterii

Migająca ikona oznacza niski stan baterii,

którą należy wymienić. (Patrz „Wymiana baterii”)

7. Podświetlenie

Użyj podświetlenia, aby obserwować zawartość

panelu LCD w zaciemnionych obszarach.

Naciskając krótko (poniżej 2 sekund) przycisk

MODE (Tryb) przy włączonym zasilaniu, można

włączyć lub wyłączyć podświetlenie. Podświetlenie

można również wyłączyć, wyłączając zasilanie

dalmierza laserowego. W tym przypadku

podświetlenie będzie wyłączone po kolejnym

włączeniu zasilania dalmierza laserowego.

5. Wyświetlanie odległości

Dalmierz COOLSHOT wykorzystujesystem priorytetu

pierwszego planu.

W przypadku uzyskania innego wyniku, niż w

przypadku operacji pojedynczego pomiaru, dalmierz

wyświetli na ekranie LCD odległość do najbliższego

celu.

np.) dokonując pomiaru na drzewie rosnącym przed

domem;

wyświetlona zostanie wartość „115 m” (odległość od

drzewa). Jest to przydatne podczas gry w golfa.

Drzewo Ogrodzenie Dom

Odległość do celu 115 m 123 m 128 m

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Nikon Coolshot in the language / languages: All languages as an attachment in your email.

The manual is 39,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Nikon Coolshot Manual

Product: