Manual Nikon Coolshot (page 39 of 139) (All languages)

570991

Zoom out

Zoom in

1/139

76 77

Übersicht über den betrieb

Vorsicht — Die Verwendung von Einstellelementen

oder Justagen oder die Ausführung von anderen

als den hierin angegebenen Verfahren können zu

einer gefährlichen Strahlenbelastung führen.

1. Legen Sie eine Batterie ins Batteriefach. (Siehe

„Wechseln der Batterie")

2. Dioptrin-Einstellung

Stellen Sie den Dioptrinwert ein, um ein klares Bild

auf dem LC-Display zu erhalten.

Drehen Sie den Dioptrin-Einstellring zuerst bis

zum vollständigen Anschlag links herum. Schalten

Sie danach das Gerät ein, um das LC-Display

zu aktivieren, wenn Sie durch den Nikon Laser-

Entfernungsmesser schauen. Drehen Sie den

Dioptrin-Einstellring im Uhrzeigersinn, bis das

Display scharf dargestellt wird.

Wird der Dioptrinwert nicht entsprechend Ihrem

Sehvermögen eingestellt, sind Sie nicht in der Lage,

Ihr Ziel korrekt zu fokussieren.

3. Messen

Stellen Sie vor der Messung sicher, dass Sie die

Maßeinheiten eingestellt haben.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

1. Drücken Sie die POWER-

Taste zum Einschalten.

2. Visieren Sie das

Ziel an.

Sofort nach dem

Einschalten.

(Initialisierung)

Standby Zielfokussierung

3. Drücken Sie die POWER-Taste einmal, um die kontinuierliche Messung

für bis zu 8 Sekunden zu aktivieren. (Die einzelne Messung ist bei

diesem Laser-Entfernungsmesser nicht verfügbar.)

Messung

4. Das interne Display zeigt jeweils für 8 Sekunden die Meldung

Entfernung“ oder „Messung fehlgeschlagen“ an. (Das

Laserstrahlzeichen blinkt.)

Messung

fehlgeschlagen oder

nicht imstande,

Entfernung zu messen.

Zeigt die

gemessene Zahl

an (Ziel 1).

Zeigt die

gemessene Zahl an

(Ziel 2).

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

5. Nach der kontinuierlichen Messung werden die gemessenen

Ergebnisse 8 Sekunden lang angezeigt und dann schaltet sich der

Entfernungsmesser ab. Wenn Sie die POWER-Taste während des

Anschaltens (während das interne Display aktiv ist) drücken, wird

eine weitere 8-Sekunden-Messung aktiv.

Visieren Sie bei der Messung einer Stange auf einem Golfplatz, z.B.,

die Stange an, so wird Ihnen die Messung leicht gelingen. Ohne

Gegenstände zwischen Ihnen und der Stange ist das kürzeste

Ergebnis die Entfernung zur Stange.

4.Wahl der Anzeigemaßeinheit

(Die Werkseinstellung ist Yard)

1. Stellen Sie sicher, dass das LC-Display eingeschaltet

ist.

2. Halten Sie die MODE-Taste gedrückt (2 Sekunden

oder länger).

3. Lassen Sie die MODE-Taste nach der Umschaltung los.

4. Nach dem Einstellen der Maßeinheit werden

Ergebnisse in die von Ihren ausgewählte Maßeinheit

konvertiert und angezeigt.

Meter [ ]Yard [ ]

6. Batterie niedrig-Anzeige

Blinkend zeigt an, dass die Batterieladung

niedrig ist und die Batterie ersetzt werden sollte,

(Siehe „Wechseln der Batterie“)

7. Hintergrundbeleuchtung

Nutzen Sie die Hintergrundbeleuchtung, um das

LD-Display im Dunkeln sehen zu können.

Durch kurzes Drücken der MODE-Taste (weniger als

2 Sekunden) bei eingeschaltetem Gerät kann die

Hintergrundbeleuchtung ein- oder ausgeschaltet

werden. Die Hintergrundbeleuchtung schaltet

sich auch aus, wenn der Entfernungsmesser

ausgeschaltet wird. In diesem Fall bleibt die

Hintergrundbeleuchtung aus, wenn der Laser-

Entfernungsmesser wieder eingeschaltet wird.

5. Entfernungsanzeige

Der COOLSHOT nutzt den Prioritätsmodus 1. Ziel.

Wenn bei einer einzelnen Messung verschiedene

Ergebnisse erzielt werden, zeigt er die Entfernung zum

nächsten Ziel auf dem LC-Display an.

z.B.) Beim Messen eines vor einem Haus stehenden Baums

„115 Meter“ (Entfernung zum Baum) wird angezeigt.

Dies ist beim Golfen nützlich.

Baum Zaun Haus

Entfernung zum Ziel 115 m 123 m 128 m

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Nikon Coolshot in the language / languages: All languages as an attachment in your email.

The manual is 39,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Nikon Coolshot Manual

Product: