212504
60
Zoom out
Zoom in
Previous page
1/239
Next page
51
2
Führen Sie den Vorlagenhalter in den Diarahmena-
dapter ein
Führen Sie den Filmstreifenhalter in den Führungsschlitz des
Diarahmenadapters ein und schieben Sie ihn bis zum Anschlag.
Die Aufnahme, die Sie scannen möchten, muss in dem Sicht-
fenster in der Metallführung zu sehen sein, das in den Scanner
eingeführt wird (siehe Abbildungen unten). Der Pfeil zeigt die
Einschubrichtung an.
Einführen des Filmstreifenhalters
1
Setzen Sie den Diarahmenadapter ein
Vergewissern Sie sich, dass die Statusleuchte nicht mehr blinkt
und führen Sie den Diarahmenadapter MA-21 in das Ein schub -
fach des Scanners ein (
25). Wenn der Vorlagenadapter kor-
rekt eingesetzt ist, beginnt der Scanner mit der Ka li brie rung.
Während der Kalibrierung blinkt die Statusleuchte (
24).
Warten Sie, bis die Statusleuchte nicht mehr blinkt.
Um Bild 1 bis 3 zu scannen, führen Sie das linke
Ende des Filmstreifenhalters in den Scanner ein.
Um Bild 4 bis 6 zu scannen, führen Sie das rechte
Ende des Filmstreifenhalters in den Scanner ein.
Position der
Metallführung für
das dritte Bild (Bild C)
Position der
Metallführung für
das zweite Bild (Bild B)
Position der
Metallführung für
das erste Bild (Bild A)
Herausnehmen des Filmstreifenhalters
Vergewissern Sie sich, dass die Statusleuchte nicht mehr
blinkt, und ziehen Sie den Filmstreifenhalter mit der Hand
aus dem Diarahmenadapter heraus. Bitte beachten Sie, dass
der Filmstreifenhalter nicht mit der Auswurftaste des Diarah-
menadapters ausgeworfen werden kann.
Entnahme des Vorlagenhalters bei Nichtbenutzung
Nehmen Sie den Filmstreifenhalter FH-3 aus dem Diarahmenadapter heraus, bevor Sie den Scanner aus-
schalten. Wenn sich beim Einschalten des Scanners ein Vorlagenhalter im Diarahmenadapter be ndet,
erhalten Sie eine Fehlermeldung. Schalten Sie den Scanner in diesem Fall wieder aus, nehmen Sie den
Vorlagenhalter aus dem Diarahmenadapter und schalten Sie den Scanner anschließend wieder ein.
Position der Metallführung für
das fünfte Bild (Bild E)
Position der Metallführung für
das vierte Bild (Bild D)
Position der Metallführung für
das sechste Bild (Bild F)
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nikon coolscan v at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nikon coolscan v in the language / languages: German, Dutch, Italian as an attachment in your email.

The manual is 20,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info