Manual Nikon Callaway RAZR (page 23 of 35) (English, French, Portuguese, Spanish)

604479

Zoom out

Zoom in

1/35

44 45

1. 『』- Repère de cible/Irradiation laser

『

』- Visez la cible. Positionnez la cible au centre du réticule.

『

』- S'affiche lorsque le laser est utilisé pour une mesure.

(Ce télémètre laser ne comporte pas de fonction de mesure unique.)

Attention: ne regardez pas dans l'objectif lorsque ce symbole est affiché.

2．『

』: Affichage de l'état distance / mesure

Indique sous forme numérique la distance mesurée en mètres / yards. Indique

aussi l'état de la mesure tel que « Measurement in progress » (mesure en cours),

« Measurement unsuccessful » (échec de la mesure) ou « Unable to measure »

(mesure impossible).

(Distance)

Affichage des résultats: ( ≧ 100m / yards) par ex. 234 mètres = 『

』

Affichage des résultats: ( ＜ 100m / yards) par ex. 76,5 yards = 『

』

『

』 -Mesure en cours

『

』 - Échec de la mesure ou mesure de distance impossible

3. 『

』Unités d'affichage

『

』Indique, en mètres, la distance en cours de mesure.

『

』Indique, en yards, la distance en cours de mesure.

4. 『

』 Indique l'état de la pile. (Reportez-vous à la section «Remplacement de la pile »)

* Bien que l'écran ACL ait été fabriqué grâce à la technologie la plus avancée, il est impossible d'éliminer toutes

les poussières. Un écran ACL affiche généralement le même grossissement ou un grossissement plus faible,

mais l'ACL de cet appareil est très agrandi grâce à la lentille de l'oculaire. Pour cette raison, de la poussière

peut apparaître comme un défaut lors d'une mesure. Cependant, la précision de la mesure n'en est pas

diminuée pour autant.

Écran interne Mode d'emploi

Attention — L'emploi de commandes, réglages ou

performances de procédure autres que ceux

spécifiés dans ce manuel peut entraîner une

exposition à des rayonnements dangereux.

1. Installez une pile dans le logement prévu

à cet effet. (Reportez-vous à la section

« Remplacement de la pile »).

2. Correction dioptrique

Réglez la correction dioptrique pour obtenir une

image nette sur l'écran ACL.

Tournez d'abord la bague de réglage dioptrique

dans le sens antihoraire jusqu'à ce qu'elle soit

totalement en butée. Ensuite, mettez l'appareil

sous tension pour activer l'écran ACL quand vous

regardez dans le Télémètre Laser Nikon. Tournez la

bague de réglage dioptrique dans le sens horaire

jusqu'à ce que l'affichage soit net.

Si la correction dioptrique ne correspond pas à

votre vue, vous aurez des difficultés à effectuer la

mise au point sur le sujet.

3. Mesure

Avant de prendre les mesures, veillez à confirmer les

paramètres du dispositif.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

1. Appuyez sur le bouton

POWER pour mettre l'appareil

sous tension.

2. Visez la cible.

Immédiatement après

la mise sous tension

(initialisation).

En veille. Cible visée.

3. Appuyez une fois sur le bouton POWER pour prendre une mesure

continue pendant 8 secondes. (Le mode mesure unique n'est pas

disponible sur ce télémètre laser).

Mesure en cours.

4. L'affichage interne affiche les témoins clignotants « distance » ou «

échec de la mesure » pendant 8 secondes. (Le signe de rayonnement

laser clignote lors de la prise de mesure).

Échec de la mesure ou

mesure de distance

impossible.

Affiche les

résultats mesurés.

(Cible 1)

Affiche les résultats

mesurés. (Cible 2)

5. Une fois la mesure continue effectuée, les résultats mesurés

s'affichent pendant 8 secondes, puis l'appareil se met hors tension.

Si vous appuyez sur le bouton POWER lorsque l'appareil est sous

tension (pendant que l'affichage interne est éclairé), une autre

mesure de 8 secondes s'initie.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Nikon Callaway RAZR in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 9,62 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Nikon Callaway RAZR Manual

Product: