Manual Nikon Callaway RAZR (page 15 of 35) (English, French, Portuguese, Spanish)

604479

Zoom out

Zoom in

1/35

28 29

1. 『』- Marca de objetivo/radiación de láser

『

』- Apunte al sujeto. Coloque el sujeto en el centro de la retícula.

『

』- Aparece mientras se está utilizando el láser para una medición.

(Este telémetro láser no incorpora función de medición simple.)

Advertencia: No mire a las lentes del objetivo mientras aparezca esta

marca.

2．『

』: Visualización de la distancia/estado de medición

Indica digitalmente la distancia medida en metros/yardas. También indica el estado

de medición como "Medición en curso", "Medición no satisfactoria" o "No se pudo

medir".

(Distancia)

Visualización de resultados: ( ≧ 100 m/yardas) p.ej. 234 metros = 『

』

Visualización de resultados: ( ＜ 100 m/yardas) p.ej. 76,5 yardas = 『

』

『

』 - Se está midiendo

『

』 - Medición fallida o no se pudo medir la distancia.

3. 『

』Unidades de visualización:

『

』Indica distancia medida en metros.

『

』Indica distancia medida en yardas.

4. 『

』 Indica el estado de la batería (consulte "Cambio de la batería")

* Aunque el LCD se fabricó empleando la tecnología más avanzada, es imposible eliminar totalmente el polvo.

Normalmente el LCD muestra la misma ampliación o menor, no obstante, el LCD de esta unidad está muy

ampliado por la lente del ocular. Debido a ello, cuando utilice este producto el polvo puede parecer un

defecto. No obstante, ello no afectará a la precisión de la medición.

Pantalla interna Resumen operativo

Precaución: La utilización de controles, ajustes o

parámetros de procedimiento distintos de los

aquí indicados puede provocar una exposición a

radiaciones peligrosas.

1. Coloque una batería en el compartimento de la

batería (consulte "Cambio de la batería")

2. Ajuste de dioptrías

Ajuste las dioptrías para conseguir una imagen clara

en el LCD.

En primer lugar gire el aro de ajuste de dioptrías en

sentido contrario al de las agujas del reloj hasta que

llegue a su tope. Después encienda el aparato para

activar el LCD cuando mire a través del telémetro

láser Nikon. Gire el aro de ajuste de dioptrías en el

sentido de las agujas del reloj hasta que la pantalla

quede enfocada.

Si no ajusta las dioptrías a su graduación, quizás no

pueda enfocar correctamente su sujeto.

3. Medición

Antes de medir asegúrese de confirmar el ajuste de

la unidad.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

1. Presione el botón

POWER para

encender.

2. Apunte al sujeto.

Inmediatamente

después del encendido

(inicializando).

Modo de espera. Apuntar al sujeto.

3. Presione el botón POWER para empezar una medición continua de

ocho segundos (en este telémetro no está disponible el modo de

medición única).

Medición

4. Durante ocho segundos la pantalla interna muestra

alternativamente los indicadores "distancia" y "no se pudo medir"

(destella la marca de radiación láser.)

Medición fallida o

no se pudo medir la

distancia.

Muestra la cifra

medida (Sujeto 1)

Muestra la cifra

medida (Sujeto 2)

5. Después de la medición continua, se visualizan los resultados

medidos durante 8 segundos y después se apaga la corriente.

Si presiona el botón POWER con el aparato encendido (con la

pantalla interna activa) se inicia otra medición de ocho segundos.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Nikon Callaway RAZR in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 9,62 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Nikon Callaway RAZR Manual

Product: