Manual Nikon Callaway RAZR (page 7 of 35) (English, French, Portuguese, Spanish)

604479

Zoom out

Zoom in

1/35

12 13

1. 『』- Target mark/Laser irradiation

『

』- Aim at the target. Position the target at the center of the reticle.

『』- Appears while the laser is being used for a measurement. (This laser

rangefinder does not feature a single measurement function.)

Warning: Do not look into the objective lenses when this mark is shown.

2．『

』: Distance/measurement status display.

Digitally indicates measured distance in meters/yards. Also indicates measuring

status such as “Measurement in progress”, “Measurement unsuccessful” or “Unable

to measure.”

(Distance)

Display of results: ( ≧ 100m/yards) e.g. 234 meters = 『

』

Display of results: ( ＜ 100m/yards) e.g. 76.5 yards = 『

』

『

』 - Now measuring

『

』 - Failure to measure or unable to measure distance.

3. 『

』Display Units:

『

』 Indicates distance being measured in meters.

『

』 Indicates distance being measured in yards.

4. 『

』 Indicates battery condition. (See "Changing Battery")

* Although the LCD is produced using the most advanced technology, it is impossible to eliminate dust

completely. An LCD usually displays at the same magnification or lower, however, the LCD of this unit is

highly magnified by the eyepiece lens. Because of this, when using this product, dust may appear as a defect.

This will not, however, affect measurement accuracy.

Internal display Operational Summary

Caution — use of controls or adjustments or

performance of procedures other than those

specified herein may result in hazardous radiation

exposure.

1. Install a battery in the battery chamber. (See

"Changing Battery")

2. Diopter adjustment

Adjust diopter to obtain a clear image in the LCD.

First, rotate the diopter adjustment ring

counterclockwise until it comes to a complete stop.

Next, turn on the power to activate the LCD when

you look through the Nikon Laser Rangefinder.

Rotate the diopter adjustment ring clockwise until

the display comes into focus.

If the diopter is not adjusted to correspond to your

eyesight, you may not be able to correctly aim at

your subject.

3. Measuring

Before measuring, be sure to confirm unit setting.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

1. Press the POWER button

for power-on.

2. Aim at the target.

Immediately

after power-on.

(Initializing)

Stand-by. Target aiming.

3. Press POWER button once to start continuous measurement for 8

seconds. (Single measurement mode is not available with this laser

rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to

measure” indicator alternately. (Laser irradiation mark is blinking.)

Failure to measure or

unable to measure

distance.

Displays the

measured figure.

(Target 1)

Displays the

measured figure.

(Target 2)

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.

5. After continuous measurement, the measured results are

displayed for 8 seconds, then power turns off. If you press the

POWER button during power-on (while the internal display is

active), another 8-second measurement starts.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Nikon Callaway RAZR in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 9,62 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Nikon Callaway RAZR Manual

Product: