Manual Nikon ARROW ID 5000 (page 36 of 41) (English, French, Portuguese, Spanish)

733849

Zoom out

Zoom in

1/41

70 71

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

Medição

Cuidado — O uso de controles e ajustes ou a execução de procedimentos que não

aqueles especificados nestas instruções podem resultar em exposição a radiações perigosas.

1. Preparação

Instale uma pilha no compartimento da pilha. (Ver "Troca da Pilha")

2. Viseira de borracha

Este telêmetro pode ser usado no seu estado atual, tanto por pessoas que usam óculos, como por pessoas sem

óculos.

3. Ajuste da dioptria

Ajuste a dioptria para obter uma imagem nítida LCD no telêmetro.

Em primeiro lugar, gire o anel de ajuste da dioptria no sentido anti-horário até que este

pare completamente. A seguir, pressione o botão POWER ON/Medição para ligar o aparelho

(confirme se o visor interno está ligado). Olhando pela lente ocular, gire o anel de ajuste de

dioptrias no sentido horário até que o LCD fique focado.

Se girar o anel demasiado, gire o várias rotações no sentido anti-horário, e ajuste de novo a

seguir.

Se a dioptria não for ajustada para corresponder à sua visão, você pode não conseguir

mirar corretamente no seu objeto.

4. Medição

Antes de medir, verifique todos ajustes de cada modo (Modo de exibição da medição/

Prioridade de primeiro alvo/Prioridade de alvo distante).

* Para informação, consulte cada seção sobre o ajuste de cada modo.

1. Ligue a energia (confirme se

o visor interno está ligado).

2. Mire no alvo.

Posicione o alvo no centro do

retículo.

Imediatamente após ligar

a energia (Inicialização).

Em espera Mira do alvo

(Desligamento automático após

aproximadamente 8 seg. sem uso.)

【Medição simples】

【Função de medição contínua】

3. Pressione o botão

POWER ON/

Medição uma vez para iniciar a

medição simples.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

4. Após a medição, o indicador "fail to measure" (falha na medição) ou

"measured distance" (distância medida) é exibido durante 8 segundos, e

depois o equipamento desliga-se. Se você pressionar o botão

POWER ON/

Medição

quando a energia estiver ligada (enquanto o visor interno estiver

iluminado), tem início uma outra medição simples.

3. Pressione o botão

POWER ON/Medição sem soltar durante

cerca de 8 segundos para iniciar a medição contínua. O visor

interno exibe o indicador "fail to measure" (falha na medição)

alternadamente com o indicador "measured distance" (distância

medida).

* A marca de irradiação laser pisca durante a medição.

* Ao soltar o botão, a medição contínua pára.

"Falha na medição"

ou "incapaz de medir"

a distância.

Exibe o número

medido (Alvo 1) Exibe o número

medido (Alvo 2)

4. Após a medição contínua, o resultado da medição final (distância

medida) é exibido durante 8 segundos, e depois o equipamento

desliga-se.

Se você pressionar o botão

POWER ON/Medição

quando

a energia estiver ligada (enquanto o visor interno estiver

iluminado), tem início uma outra medição.

Medição "Falha na medição" ou

"incapaz de medir" a

distância.

Exibe o número medido

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Nikon ARROW ID 5000 in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 11,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Nikon ARROW ID 5000 Manual

Product: